In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Dear nRF experts. We are a module manufacturer and we have designed an nRF45L15 module. We are doing a series of verifications. When we were doing the connection test, we...
Hi,
I use Nordic connect SDK and have to create a new revision for a custom board, because there are some hardware changes. I managed to create an overlay for the new revision...
MCUBOOT contains a flag MCUBOOT_OVERWRITE_ONLY_KEEP_BACKUP that stops it erasing a big chunk of the start of the secondary image after an update.
We would like to set this...
I'm looking for an nrfutil command to replace this command:
nrfjprog --memwr 0x10001080 --val 0x12345678
My goal is to write a serial number to the UICR CUSTOMER[0] register...
Hi All,
I have nRF54l15-PDK board which has 8MB of external flash. Currently I am exploring on basic read/write functionality on external flash.
I am using nrf sdk version...
I'm checking the function by uploading the code to the pcb that uploaded the nrf9160 chip.
I checked that the network communication is normal on the previous 9160dk board...
Hello,
I have just received the nRF5340-DK development kit. However, when I plug in the USB cable to my PC, it's not detected. I have tried multiple USB ports and the issue...
i'm working "bare-metal" with the nRF54-DK, loading from the command-line by directly calling JLink....
often (but not always) i receive the following message from JLink...
Hi there
I'm using two nRF52840 boards and I want to set them up to relay a message from one phone to another like this: phoneA > board1 > board2 > phoneB.
I have looked...
In attempting to set up the nPM1300-EK for battery characterization, I keep seeing the connection status "PMIC Not powered" and repeating errors: "module_pmic: No response...
Hello everyone,
I am working on a project using the nRF52840 with Zephyr and SDK 2.5.2. Recently, I sent a request to register my company for Bluetooth, and I received the...
I am using "nrfjprog -p" to reset our nordic devices in our test rigs. We recently migrated the setup to RHEL 9 and now we are seeing regular failures in nrfjprog due to ...
Hi,
We are looking to add an nRF54L15 chip to our custom nRF9151 board, to support Bluetooth. We also would like to add NFC functionality and additional GPIO pins from...
Product: nRF54L15, SDK: V2.9.0
Application: Matter + BLE multi-protocol
Hi,
we want to store X509 certificates in secure storage. I went went through Nordic supplied...
As shown in the figure, is the tool "Online Power Profiler for Wi-Fi"
TWT event length includes: crystal ramp-up, initialization, start radio, receive, transmit , and enter...
