Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
HI! I'm on Windows x86 and I've followed the steps from the getting started assistant. After trying to locate the board directory ncs/zephyr/boards/arm/nrf9160_pca10090 ,...
I am doing a custom desk for a client and I had this idea of adding a electromagnetic lock on a drawer. That is easy enough but I thought that maybe I could add a couple of...
Hello If I an exemple like ble_thread_dyn_mtd_coap_cli and that I configure the mode in MULTIPROTOCOL_802154_MODE_FAST_SWITCHING_TIMES: do you have any idea how long it takes...
I have two SPI buses on my board, with a different type of slave chip on each. Only a few bytes are read from each during boot. When I use SPIM0, 1 or 2 for them there is...
Newbie here simply trying to run some example projects from the SDK.
Setup:
Segger Embedded Studio 5.10b
Tried example projects in both SDK v17 and v16
nRF52 DK...
We have a working app for SDK 16 and freeRTOS. We wanted to update to SDK 17.0.2 but after upgrading the app hangs up at the first vTaskDelay(). We use configUSE_TICKLESS_IDLE...
Hello, I am a newbie in this forum and I'm not very familiar with app development in general, however I am in the situation in which I have to develop an app to acquire ANT...
Hello Nordic Team,
I am having issues with the HCI UART firmware for the nRF52840 on the Thingy91. I have been using the HCI UART firmware from nRF Connect SDK 1.0.0 for...
Hi, I am working on a project to send commands from mobile to device and vice versa. I am using nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_template . I have made...
Hello,
I am using : SDK 17.0.2 and S132_7.2.0 with nrf52832 DK
in my BLE application, the FDS has 2 behaviors :
1) When the softdevice is enabled : fds_write returns...
Hello,
I´m searching some information about the NB-IoT protocol stack and the overhead which is send with every message.
I nearly searched the whole net but didn't find...
Hi,
It has been stated that nRF9160 doesn't support RLC UNACK, which we have also observed with nRF9160-DK in signalling mode against radio communication tester. Are there...
Hi,
I have a setup where mobile device(central) connect to nrf51dk (peripheral) and exchange data for a time. I want to detect unplanned disconnection of mobile device in...
Hi all, I try read DEVICEID in non-secure application but always return "BUS FAULT", I tried too enable NRF_FICR register in "spm.c" but the error persist!
I try
NRF_FICR_S...
Good morning Nordic,
I am trying to configure the I2C pins for our board (using nRF5340-QKAA SoC) but I cannot find the pin numbers for I2C_SDA and I2C_SCL.
All I could...
