Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
Hi,
I want to change the bit rate in Mesh light switch example for long range (as of now getting only 15mtrs), i found that there is a function for update phys, but while...
Dear all,
I'm using an nRF51822 chip for implementing a BLE HID device (SDK ver. 12.3.0, SD ver. s130_2.0.1)
Situation is the following:
1. I use peer manager for deal...
I've written a detailed description of how to program & debug the NRF52832 using open-source tools and the Nordic SDK.
See https://iosoft.blog/arm-gcc-lean-nordic-nrf52...
Hi all
I am working on Bluetooth application using NRF52840 kit. The application is very simple, the device would have about 7 push buttons which when pressed data will...
During testing of SDK for Mesh v3.2.0 I noticed that it's no longer possible to send a request and response using SAR where both models are on the same element. This was possible...
Dear All,
On the NRF52840 AD6 and AD4 are for USB D+ and D-, in the case I have no need to route USB signal can I use these 2 lines for General Purpose I/O especially high...
Hi
I have some questions that need your help.But it seems that there is no answer yet.The following is my questions link.
https://devzone.nordicsemi.com/f/nordic-q-a/52060...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
Hi!
I searched the devzone and there is quite few topics about how the relay is enabled / disabled in the FW... according to https://www.youtube.com/watch?v=r9CvtbCmYQY...
Hi,
I'm unable to hit my break points while using the J-link Lite debugger.
Mostly, after I've attached the debugger and reset, it goes to the correct location
FUNC_NORETURN...
Hi,
I am using the nrf51422 controller and other controller which contains Bluetooth .The nrf51422 Bluetooth is central and other controller Bluetooth is peripheral.I am...
Hi to all,
I am using nRF52832 DK with SDK 15.0 version. My two nRF52 DK damaged while debugging I am a little bit confused why this happening.
When I debugging I used...
Hi,
I need a way to dynamically disable watchdog when I do MMD debugging. I found the old trick, check bit 0 on CoreDebug->DHCSR, does not work any more in MMD. Is that...
I suspect a possible race condition happening during NUS service discoveries. I have two peripherals that are advertising and have DIS, Battery and the NUS service enabled...
Hello,
I have configured max30101 with nrf51 and I want to read the fifo of max30101. The fifo can contain 32 samples and the size of each sample could vary from 3-9 bytes...
