Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi
I installed nRFConnect v2.6 and command line v9.8.1 and want to use PPK to measure current.
When first connect, it will update FW into PPK and works well to measure...
Hi. I have been going through the mesh examples. Now i need to know how to send pings between any two nodes in the mesh. My aim is to first be able to successfully ping a...
I am trying to broadcast a non-connectable advertisement (such as a beacon) while I am connected to a device that I am transferring data via TX. I am working with a nRF52840...
Good morning everyone,
I am struggling since a few days to understand how the SPI communication is supposed to work in the SDK 15.0.0....
So far, I am having some issues...
Hi Nordic,
I am using the example in SDK15, ble_central_and_peripheral -> ble_app_interactive. After being connected to a device, and after pairing. I am trying to make...
hi......
i want to sense the temperature and send data to the uart app via ble ... so i want to merge two programs uart and twi sensor
i have tried but it shows error...
Use central-peripheral programs. First advertising and then scan. It was found that during the adveristing the program was running normally, but the adveristing signal could...
Hi:
How to get sine_table[] data,like this.
int16_t sine_table[]= {0,0,23170,23170,32767,32767,23170,0,0,-23170,-23170,-32768,-32768,-23170,-23170};
NRF_I2S->TXD.PTR...
Dear Nordic Team,
Thanks for supporting.
I am working in ble_app_uart_c example in this example is automatically connect with its peripheral. But i need to connect and...
Hi Nordic,
Here is my configuration:
HW: Customize nRF52840
SW: blinky_rtc_FreeRTOS_pca10056
Problem: The led blink for a few sec and the board went into vPortSuppressTicksAndSleep...
I have a nordic nrf52832 dev board acting as peripheral and my client device is huawei honor 9 lite. I'm trying to send two packets (or 45 Bytes data) in one connection interval...
Hi,
I want to know how to send data with 52840Dongle with ble to the mobile, I tried to use the "ble_uart" program of 52840DK, I followed a tutorial, performed a full erase...
Hi,
Is there out of band data available for the Rx path? I want to make sure there is no interference from other bands and if a filter is already implemented in the IC RF...
Dear Team,
I am using NRF52840 for ble_app_beacon and working fine. Now I want to extend the range using 'PHY_CODED' option. Please let me know in this ' ble_app_beacon...