Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I now need to make a program on nrf5340 audio DK, SDK v3.0.2 to scan auracast and print the information in the subgroup in PA, without sink BIS.
In addition, it needs to...
Hello,
I am trying to use the drivers from the following repository: https://github.com/too1/ncs-arducam-mega-driver
I and using the latest version of the NCS 2.2.0, I...
Hello,
I get this error when I try `nrfutil device list`, and any other nrfutil device command.
However, if I use `nrfutil device --jlink-dll /path/to/libjlinkarm.so...
Hello,
My name is Jeon. I am using the RTC function on a custom board that utilizes the same chipset as the nRF9151. I have configured the RTC to trigger an alarm every...
Hello,
I need to make the OTA DFU work and I followed the instructions here: https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/subsys/mgmt/mcumgr/smp_svr...
Hi,
Please note that we are having below setup
Module: nRF52832 based HolyIoT YJ-16048 Module SDK: NRF 17.0.2 Tools: Power Profiler Kit II
Expected current consumption...
Greetings,
Does anyone know if there are updates planned for the Arduino IDE with the latest SoftDevice versions? I opened this issue on GitHub: https://github.com/sandeepmistry...
I am using NCS 3.0.2 + VSCode to develop for the nRF54L15 . I have two projects:
\nrf\samples\bootloader\src
\nrf\samples\esb_prx
Since my custom board...
The instructions for running the sample are too difficult to follow. Here is why/where:
>>The sample also requires a device running a CTS Server to connect with (for example...
I am using nrf 52840dk board i need to know how to reset the devlopment using software reset when we press the Button 1 in the nrf 52840dk board
1. Give some software reset...
Hello,
I want to Configure a UART RX pin as GPIO and use it as a Wake - up interrupt pin before going to sleep. Is this possible in nrf54l15?
I tried to do so, but I was...
I've been having problems getting nRF Connect to flash a target through my J-Link programmer lately, even though it has historically worked fine. I suspected the issue might...
Hello, I want to flash a test application to the nrf52820(on the 52833DK(it supports both 33 and 20) for test purposes. I first flashed the softdevice and the bootloader....
Hello everyone,
I've noticed that when using MCUBoot+External Flash+OpenThread+FOTA over BLE+PWM, the program startup time is extremely long, reaching 1684 milliseconds...
