Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi,
I'm not sure if SES support C++ compiler in nRF9160 project, I did add C++ source in CMakeList:
target_sources(app PRIVATE src/xxx.cpp)
It won't work, Does anyone...
hi,
I use the SDK16.0 ,to develop BLE touchpad on nRF52833,which is should set non-zero value for feature reports . And now,i have a problem,how to implement the FEATURE...
I made a custom board using nRF9160 and tested a very simple program.
However, it consumes high current compared to nRF9160 DK. I measured current flowing on VCC line of...
nRF52832 / SDK 14.2 / SD5.1.0
There might be two configurations to setup a PPI channel to assign some peripheral event to both timer capture & clear task:
nrf_drv_ppi_channel_assign...
Hello all,
Having a smallish problem seeing printk() output on my board. My board is an NRF9160 PCA10090 inspired board. Long story short, I can't see printk() stuff showing...
My application implements a beacon with services, and a buttonless BLE bootloader.
The application can start the bootloader in two ways.
The first method is executed locally...
Hi,
I am in the process of provisioning and configuring a 2-element light switch server node and a common light switch server. I am using the orginal exemple for the provisioner...
I'm attempting to transfer 256K bps (1 244-byte notification every ~7.5ms) using an nRF52840 using Notifications and am not getting close to the necessary bandwidth. I'm getting...
Hi,
We are developing an application requiring the DFU Service on nRF52832.
The implementation of the DFU Service without bonds works very well, but when switching to...
I've been able to connect to our server using the LTE modem sample app.
As shown below, I configure the modem, open a socket, bind the port, and send and receive a small...
As I'm working on debugging a problem where a TLS connection silently fails with no error code, it occurs to me that it would be VERY handy to have a way to connect wireshark...
In using the Thingy52 I can't figure out how to just get the just XY coordinates from the motion sensor - or any other sensor. I'm trying to figure out if I can capture motion...
hi, i am a student, i am new to nrf52840 DK. I downloaded Gooligmelec "nrf52test-led-battery" from github and open Solution inside SES . it was running ok. when suddenly....
Hello,
I am using nrf52840 and SDK 15.3.0. and the device wakes up every hour and every day for reporting data.
So I am using app timer to wake up also using app_timer...
Hi,
I am working on nrf52840 and using below SDK and softdevice.
SDK - 16.0
Softdevice - S140
IDE - embedded segger studio.
currently using nRF52840-DK.
I am using...
