At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello,
I am trying to use TIMER3 where it should count 1ms ticks for 15 seconds and then stop.
Tried the below code. However it never enters ISR.
Please let me know...
Hello,
I have a Insight ISP4520 SIp which include a nRF52832 chip and a SX1261 for Lora radio https://www.insightsip.com/products/combo-smart-modules/isp4520 The internal...
I'm using
the nRF52840 DK and the Matter light_bulb example, SDK v2.7.0.
a raspberry pi with the nRF dongle as a thread border router
the chip-tool running and compiled...
Al over these example programs there are all these messages like
LOG_INF ( "Filters matched. Address: %s connectable: %d " ,
addr , connectable );
How do you actually...
Hi,
We are using nrf52840 with nrfSDK-16.0. We have implemented extended advertisement in BLE 5 LE CODED PHY. We want to try periodic advertisements. Do we have any examples...
My custom device uses nRF9151 and we're using SDK 2.6.0 with modem firmware 2.0.1.
When the device connects to the LTE network it derives a default APN, however, my provider...
Hi,
I’m exploring the use of the Thread/Matter protocol for a smart lighting system. My goal is to have the system communicate seamlessly with the cloud—allowing commands...
I am using a LattePanda 3 Delta running an Ubuntu server OS (x86) headlessly. I am using a RS-232 cable to obtain the modem trace from my custom board, which uses an nRF9160...
Hi,
We are currently starting a project using the nRF52832 as our controller, Segger Embedded Studio 5.42a as our IDE, and nRF5 SDK version 17.0.2.
Project Requirement...
I have found a bug in SDK v2.6.0 at zephyr/drivers/flash/nrf_qspi_nor.c while erasing the external MX25R64 flash.
Environment:
nRF5340 DK Hardware (MX25R64 external...
Hi
We use the nRF52840 (aQFN73) with a 4-layer 1.6 mm PCB for our current project. The top and bottom layers are for signals, the two internal layers are ground and power...
HW: nRF5340DK NCS: v2.8.0
After installing NCS v2.8.0 from ToolchainManager, I tried to build the project but failed.Error message "No such file or directory: LIBGCC_FILE_NAME...
I have a Raspberry Pi Pico which is powered by a Lipo battery. I want to measure the current with the Power Profiler Kit II. I hooked the 2 grounds to to the board, and VIN...
I am using BLE mesh in nrf52840. I have modified the sensor server sample and sensor client sample to suit my requirements. I am using toolchain and sdk v2.6.1. It is working...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
