Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I have a custom board based on the nRF9160 SICA SIP, using only NB-IoT with a lock on a single frequency. GPS is disabled, and there are other peripherals connected...
HI,
We have two products that work together. One uses the nrf52832 and the other nrf5340. Using the Programmer (3.0.9) we can take a factory fresh 5340 Erase all and program...
Please refer screen shot attach I am able to configure uart0 but not able to configure uart1,2,3
i am receiving multiple errors while same code is working fine for uart0...
Hi, I recently moved a project from one computer to another and the files and all the include directories were in a mess. I cleaned up most missing files and moved directories...
Hello! I am using nRF Connect SDK 2.6.0v. I want to enter the device into deep sleep mode when i press the button 2 sec When Next time I press the button 2 sec, wake up from...
Hi!
This question has been asked before in various forms, but none of the answers I've seen will work;
Is there a way to get any callback before or after a BLE Advertisement...
Hi all,
i am using NCS 2.4.0
I have a question is there any possible that i can use double slot to update firmware over BLE FOTA?
I already look at the website below...
Hello, I am currently working on a custom board that contains the E73-2G4M08S1C module. This module contains the nRF52840 chip. My goal is to exit System On periodically every...
How to create multiple BLE connections, one just advertising and another allowing connections with different names with the nrf Connect SDK in the peripheral_HR example?
Hello Nordic team,
I am using nPM1300 and nRF5340 in my custom board. I am using also Renata ICP621333PA-01 battery in my design. In order to prolong the battery life, I...
I am using a Mikroe development board with the nRF9160 to establish an LTE connection and send MQTT messages to a broker. The application successfully connects to the network...
I have used the nRF52832 on a few dozen projects, usually at 3.3V etc. On this project I have it at 1.8V, which may be related, but spec is 1.7V min, and the 1.8V supply is...
Hi Noridic team,
I am developing with nRF5340, and I added the following configuration to the prj file:
CONFIG_SPI_NOR_INIT_PRIORITY=75
However, I got the following...
Hi, I cannot compile because of the error below. Thank you in advance for any help.
I have updated the toolchain and sdk recently. Tried also with 2.6.1 and 2.7.0, the same...
