SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hello,
I am working on nRF52840 custom board, in that, I was facing issues with sd_softdevice_enable().
When I call the sd_softdevice_enable() it's stuck. Not return from...
Im using SPI interface to read data from https://docs.rs-online.com/7d34/0900766b81327f26.pdf using the D2 opcode.
The opcode starts reading the page from the flash (528...
Hi,
we are not able to see any output in NRF connect APP in FFBM mode with DTM Firmware,
However , on flashing complete firmware, we are able to turn on Beeper in FFBM...
Hello Nordic support,
I have a Zigbee coordinator application which has declared the time cluster as a server. I have a zigbee end device which has a time cluster as a client...
Hello I'm using nRF53 DK on zephyr v1.6.1. I'm now testing the power-saving mode. I tested the system-off example "v1.6.1/zephyr/samples/boards/nrf/system_off" and it works...
Hi,
I am using nrf52810 chip. we are trying multilink with central(1 central and two peripherals connected at a time),one central and one peripheral is fine, but we are...
Works on Huawei P20 Lite (Android v9), Samsung J3 (Android v7.1.1), all IOS phones. Doesn't work on Samsung A50.
Samsung A50 does see the devkit when using the same firmware...
OK, full disclosure - I'm pretty new to the whole nRF Connect/Nordic Semi environment, having had to jump across here after all the issues with silicon availability meant...
I would like to configure GPIOs as compatible = "nordic,nrf-gpio"; in devicetree file.
I did check this topic, but I think that this kind of configuration defeats the whole...
Hi, I'm working on a FreeRTOS (I just start to use it, so I'm a beginner) project in wish we want to use an external 32 MHz crystal. The program has a task that should be...
I want to implement CENTRAL using nRF52810. To implement the central, the softdevice must be s132 but I am not familiar with the softdevice concept. Until now, the softdevice...
Hello,
I closed below case by mistake.
nRF9160 receives garbage data on UART sometimes - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
As per your...
The Thingy:52 application uses LIS2DH in low power standby mode and the MPU-9250 for advanced motion tracking.
Why machine_learning firmware used LIS2DH sensor instead of...
Hello developers,
I am using nRF52840 feather from adafruit as a ble central board.
FIrst of all, I tried to filter just only for my beacons with UUID. I saw a ble central...
