Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I've a custom board which has NRF51822 SOC and STM32 SOC. These two are connected over UART. In past I've successfully performed DFU OTA (BLE) for nrf51822 MCU, and...
I have got a Raytac module MDBT40(nRF51822) and development board nRF52832. Now I want to program the module using the development board. I have followed this video ( Programming...
Hello all,
I am trying to update my firmware using BLE peripheral.
I followed the instructions in this [tutorial] ( devzone.nordicsemi.com/.../)
I downloaded the SoftDevice...
Hello Nordic Forum!
Our product relies heavily in the TWI Bus, we use it to communicate with different sensors periodically. The most "important" one is read once every...
Hi,
We have made a custom board using the NRF52832 chip. The device is in hard fault mode and we believe it may be because of the corruption in internal memory. We wanted...
Hi,
Currently I am trying to test DCDC mode on my custom board nrf52832. After soldering 15nH and 10uH on DCC(pin 47), I issued the following command after softdevice enabled...
@Vidar: I have followed your steps in tutorial for "Development with GCC and Eclipse" and when I try to flash my device I get the below error
Nrfjprog.exe is not being...
Like many others (read a lot of threads here about this and also beneath the tutorial to Eclipse many people write that they suffer for it) i have problems in Eclipse with...
Hi,
I'm using the example dfu/bootloader_secure_ble for NRF52832 (PCA10040 board) in nRF SDK 13.0.0 version and on my mobile the "nRF Connect" application.
If I use...
Hello,
I'm working on a project based on the ble_app_multirole_lesc example, under examples/ble_central_and_peripheral/experimental and I found a bug.
In ble_evt_dispatch...
Hi,
I am using nrf52832 with sdk11 and s132.I am using ble_app_beacon example wherein I want to advertise with different address after one power cycle.
In ble_stack_init...
I have uploaded the Image with Keil µVision compilation errors, included Files in main.c and on the left side the compilation of micro_ecc_lib_nrf52.lib file using " build_all...
Hi there,
I'm trying to do a DFU over BLE using the Nordic nRF5x SDK on version 14.2. I'm using an NRF51 dongle on the PC side while trying to transmit to an NRF52832,...
I am using a nRF52 to communicate using both BLE and proprietary protocols. When using BLE, I apply the workarounnd for errata 102 and 106. However, when I switch to my proprietary...
