Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
I am using ncs 1.0.0 and modem fw version 1.0.1.
I am using PSM mode in my firmware.
I want to toggle state of one gpio when modem goes in active or inactive state...
Hi.
I am developing application with mpu6050 gyro on nRF52832, swd S132 V6.1.1., sdk 15.2. My code is based on ble_app_uart. In main, I add my custom function that calculates...
Hello!
I was going to start to program my Thingy 91 but since I don't have a J Link Programmer cable or a nRF9160 DK. I was planning to use mcuboot like suggest this documentation...
Hi,
I am working with MPU6050 gyro. I run the examples from GitHub for nRF52. Everything works fine, bit I have an issue with gyro output data. In register map documentation...
I'm new to Nordic, I just got an nRF 52 DK. Refreshingly simple to get working with Segger Embedded Studio on Mac. I'm particularly interested in the BLE multiperipheral application...
Hi,
I'm trying to build the asset tracker off the master branch in windows 7. I did do west update. Using gcc version 7.3.1 20180622
It fails like below. Any ideas?
...
Hello,
I have the following issue. I am developing an application very similar to the "ble app hids keyboard" example. SDK 15.0, S132 V6.0.0, nrf52832.
I would like to...
Hi!
Previous tickets 234795 and 231307 asked about the status of field updates of the nRF9160 modem firmware. Some solution is coming, but unclear when.
Are there any...
We are developing with the nRF52840, in this instance present in a Laird BL654 module carried by their DVK-BL654 dev board.
After trying three separate examples that attempt...
Hi all,
I need to be able to reprogram an nRF52832 on a daughterboard from a mainboard with a Cortex M7. I have been able to eraseall and reprogram the nRF52, but it seems...
I have searched this site and not found an answer, although this seems to be a similar question: https://devzone.nordicsemi.com/f/nordic-q-a/41853/usb-driver-install-fail...
Hi,
I am stuck in sending and receiving serial data over Rx and Tx in nrf51 DK. I used arduino to prototype a fingerprint access control system. Now I am shifting to nrf51...
Hi,
I would like to know if the LFCLK is enabled after zboss_start(); and after zboss_start_no_autostart().
I would like to use an rtc event to trigger a PPI routine and...
Question: for the nRF52840, if I configure a GPIO pin as an open-drain output (DRIVE setting of S0D1) and then select this pin as a UART transmit pin, does the open drain...
1 .after the flashing the board i get a Zigbee Connection and Bluetooth connection but i can't able to control the bulb by using both board and bluettoth
2. Sir i am using...
