Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello,
I encountered a problem while trying to bond a nrf54L15 (central) with a nrf52810 (peripheral). The firmware of the nrf54 is using Nordic Connect SDK and the nrf52...
Hello,
I hope you are well.
I have a code inside the connection connected callback that sets the MTU to the maximum, which is working fine on ncs v3.0.2 but generates...
Hi everyone,
I’m currently working with the nRF9151-LACA-A1A-R module, developing NTN communication features using SLM mode. However, I haven’t been able to find any documentation...
"I am using nRF Connect SDK (NCS) v3.1.0 and developed BLE DFU functionality by referencing the Nordic Semiconductor Academy course: ' Exercise 5: FOTA over Bluetooth Low...
Hello,
I use nRF5 SDK and nRF52833. Now I want to do the radio test at the "examples\ble_peripheral\ble_app_uart".
When I use radio_test_init(&m_test_config); or other...
I am currently trying to claim my nRF9151DK on the nrf cloud. I went through the Quick Start steps and activated my SIM card but my device has been stuck in this state for...
Hello,
I am currently testing the Matter Closure sample with an nRF5340-DK board. I am using nRF SDK 3.2.0.
- When I send an open command, everything works fine.
- When...
I'm trying to make the basic Button sample work but am having problems.
The physical button is a latching button. Press it and it moves in with a click and physically stays...
nRF52832 Product Specification V1.4, page 344 lists predefined baud rates only.
Is it possible to use other values for custom baud rate, and if so, what is the relationship...
We have noticed an issue with received characters being dropped on the UART shell interface. Originally, we found the issue using our own application, but subsequently we...
I am using a nrf54l10 module on the pcb and using the nrf54l15 dev board. So I have a bootloader, the mcuboot, and then the image. I program over SWD on the pcb. So my problem...
Hello!
What would be the best way to start a custom LE Audio application with a different codec?
I mainly want to evaluate being able to stream 2-4 channels from a 53...
Hi,
I am using the npm2100 as a power management chip in my product, utilizing only the boost function. When only the npm2100 is soldered on the PCB with no load connected...
I am using nPM1300 MIKROE Click with ESP32 over I2C and enter ship mode by writing the required I2C registers from ESP32 .
Observed Behavior
Ship mode command is sent...
Hi,
I am developing a feature to add remote provisioning support to a BLE Mesh-based network. In the network, a provisioner node receives, via a serial command, the UUID...
