But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
We have a custom PCB with external crystal for HFCLK. Can you tell whether the external crystal is used by default for HFCLK or it has to be selected in the HFCLKSTAT...
I am using timer 3 as a counter for my capacitor discharge time. Currently, the value of is always problematic because it shows with too many deviation values sometimes...
Hello,
Is there any user manual to the nRF Connect for Android? I guess it is quite simple tool, but I am complete beginner in the BLE and would appreciate some description...
Hello All,
Currently we have a nRF52832 firmware .hex file for mass production.
And we use "nrf connect - programmer" to firmware programming without any problem.
...
Hi!
I'm updating to SDK v1.7.1 and I am looking at the changes in LwM2M Carrier Library v0.20.1. I was previously using LwM2M Carrier LIbrary v0.10.2
The big change is...
Hello,
I'm trying to install circuitpython onto an nrf52833 dk board, and am running into a fair amount of trouble.
Wondering if anyone can provide a guide on the explicit...
Hello,
I am trying to port the 51822 project to 52833. I am testing the port to 52832 temporarily.
The 51822 project is a commercial product.
SDK – 17.1.0 SD-S132, PCA10040...
Hi ,
I check the datatsheet "nRF21540_PS_v1.0.pdf" but I confuse on page 22 "TX_Gain initialized with POUTA_PROD (20 dBm +/- 0.5 dB)".
Which one is correct??
1: Tx gain...
I’m trying to use the Power Profiler app v3.2.0 under nRFConnect for Desktop v3.9.1 with a PPK 1 attached to an nRF52 DK board (containing the 52832 processor), but am having...
Hello, i'm having trouble with my new Board Nrf5340, i cannot detect the board to my PC.
I connected with micro USB and when i'm going to the device manager, i'm not seeing...
Problem:
Tried to compile (west build --board nr52dk_nr52832) the C:\nRF\v1.7.1\nrf\samples\peripheral\lpuart project but it failed to compile. I discovered this after updating...
Hello All,
I am new to use Segger Embedded Studio and NINA-B406 module. I have installed Segger Embedded Studio V5.50d and EVK of NINA-B406 module having nrf52833 SoC. ...
Hello All,
I have taken usbd_ble_uart_freertos example and modified it for USB MIDI example (taken from Github) for nRF5 SDK and modified it to use nRF52833 SoC.
I am...
