I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi,
I worked few years ago on a project with the configuration below :
nRF Mesh SDK V1.0.1
nRF52832
I used the light switch example where the client and the provisioner...
Hi, I have built a project upon the aws_iot-example. There are three shadow-topics that the device may publish to (/update, /get and /delete). To me it seems there is no possibility...
So I'm trying to get to grips with the ble_app_blinky example from nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_blinky
To start with I grabbed the hex file ble_app_blinky_pca10059_s140...
Hi, 1. In ncs v1.5.0 nRF5340 I need to drive a spi peripheral w25q128 2. How do I generate this file?
3. Where can I find the syntax rules that generated this file? 4. Can...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
Hi,
I have a custom board with nrf52840 with UARTE1 instance enabled for RS485 communication.
I have 2 boards on the same configuration and trying to send data to each...
Hello,
I am trying to use a nRF52840 Dongle to perform DFU over Thread: I am using a PCA10059 board, already provided with the default bootloader. I also programmed the...
Hello,
I am in a project using nRF52 board where I develop and Android app.
The application is using Android stock BLuetoothLeScanner to scan for devices. After that the...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
I use whitelist to store bonding information. This bonding information is written to the flash area using...
So...I have an idle task running then a UART interrupt fires upon a character being sent over the serial, and somewhere during the execution of the ISR, it attempts to execute...
I am using the NRF9160DK, I have already made all the getting started and compiled an example to use the LEDs on the board with em studio. I had already connected my card...
Hello,
I am trying to send some sensor information via thread / mqttsn every 5 min. Therefore. The dongle has to wake up (5 sec.), send the information and return to sleep...
Hi friend,
I used SDK16.0 and softdevice is S140. I modified ble_nus_c to a custom 128-bit UUID. It has 1 service (0x0211) and 3 characteristics (0x0212, 0x0213,0x0214)...
Hi,
I'm testing the aws-FreeRTOS code.
In detail, It's a BLE test
The problem is, BLE can connetc in the test but next step (read/write) cannot
BLE connect apple...
Would it be possible to illustrate what AT commands would be required to set up and send a UDP packet for the nRF9160, including configuring the modem, turning the modem on...
