Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi There - I'm very new to electronic design and need help making a key design decision. Specifically I want to know that the performance will not be a problem when writing...
Hi
On some devices we see in the production a shortcut between the BT antenna and the P0.18 pin on the 52811. The cause can be extremely warm weather at the production facility...
Hello,
We are tweaking the TLS connection between nrf91 and mosquitto.
What ciphers does the modem support? Is there a list available?
Best regards,
Vlad
I want to send a byte on Nrf connect app upon receiving an GPIO interrupt using BLE_APP_UART code. I have configured pin P0.10 for the GPIO interrupt. I am using SDK15.2.0...
Dear guys,
I am implementing a module that monitors the battery voltage for our tracker device using NRF9160.
I do not understand how to set up two parameters for the...
Hi:
The urgent problem we are facing now is:
debugging hci_usb on Linux, how to set MAC address and send/receive files ? hci_usb fw : \ncs\v1.3.0\zephyr\samples\bluetooth...
Hi, I have no found clear steps to create DFU zip packet for old one softdevice S132 SoftDevice v2.0.0.
I try to build with nrfutil pkg generate but seems its working only...
Hi,
We are currently trying the Long Range (Coded PHY) on our advertised message, but we can't see any improvement (range of about 50meters). The range can even be smaller...
Hello,
I'm using a NRF52832 with SoftDevice s132 v7.0. I also have freertos. I have an app which advertises and scans. The app is set up to trigger a break point on assertions...
I have some customers seeing an issue with advertising/connection after successful DFU. Everything was working before DFU. The changes in the new firmware have nothing to...
I am trying to port the examples/ble_central/ble_app_hrs_c project from the 52840/pca10056/s140 to a 52833/pca10100/s140 project.
Having trouble in the port from the nrf52840...
Hello, I'm using softdevice 6.0, SDK 15.0, secure bootloader buttonless S132. On the phone with Android I'm using: nRF Toolbox 2.9.0 with DFU Library version 1.10.3.
I start...
I have built a custom chip with nrf52840 on it.
I use Ses as development tool.
I took as startingpoint for software SDK15.3 with Softdevice 140
I took the ble_template...
I use SES for debugging,
the chip is nrf52840 with softdevice 140, sdk 15.3
I ported a project from 2017 and now I'm ready to compile all without any error,
but as...
