This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello Nordic Team,
I am working on OTA functionality using nRF Connect SDK 2.9.0 on the nRF52833 controller.
Earlier, my application size was around 320 KB, and I reduced...
Good afternoon,
My device communicates using MQTT a few times a day. After many connections I noticed that communications stopped. Every connection attempt would fail with...
Hello all,
I need to sniff some packets to fix an BLE issue, but I can't find the hex files to program my nRF52840 Dongle. The links provided in the documentation and website...
Hi, I tried to start toolchain manager on my main computer and its not working anymore. I tried to delete all nrf related folders, deleted all apps including nrf connect deskop...
Here is a focused support ticket description for your actual issue:
Device: nRF5340 DK ( nrf5340dk_nrf5340_cpuapp ) SDK Version: nRF Connect SDK v2.5.1 Modem: Quectel...
Hello, I'm working with Power Profiler Kit II and i see that we can use a digital port. I would like to know what the electrical levels for a valid High and Low. I can't find...
Hello, Currently I am working with the nrf connect SDK version 2.8.0 with an nrf5340 SoC. There is no external flash memory. I am trying to build a bootloader with the serial...
I have created a Zephyr Snippet (derived from the cdc-acm-console sample).
I am unable to select it in the Build Configuration. It is listed in the dropbox where the sample...
Hi,
I previously had access to the nRF54L15 Early Access SDK and toolchain, and my local EA workspace has been lost. I need to rebuild my development environment for a project...
Hello,
I am currently implementing a Central device using the nRF52810 as part of a Gateway board.
I intend to connect the antenna via a U.FL connector . My current design...
Is it advisable to POT circuits using the nRF9151? If so, please advise of any precautions. The IOT product that I'm designing requires to be intrinsically safe. As such,...
Hello:
I am developing a board and shields based on nRF5340 (but this question is not really specific to nRF5340, it also applies to most other nRF5x chips). The main-board...
Dear Nordic Experts,
Hello,
i have defined a custom service containing a custom char. value in a peripheral according to https://github.com/NordicPlayground/nRF5x-custom...
Hello,
I am running into an issue when trying to use both GPIO and I2C peripherals on the same set of pins on an nRF54L15 board. I have an I2C bus configured on two pins...
I have two devices on TI CC2538 that having problems talking to the NRF52840 dongle.
The channel is channel 11
There are 8 devices using TI CC2538. Only two of them...
