This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi -
Using nrf5340 and ncs 2.1/2.7
To ensure we are testing and integrating the originally released bootloaders and net core images, we'd like to be able to use `west...
Hello,
after an attemp to switch to UF2 Bootloader from Open Bootloader my Makedriary nRF52840 MDK USB Dongle stopped working (now shows only the green led always on) and...
I am getting an error when trying to get a nRF9161 application to connect to a private APN using some PDN configurations.
The error is:
I have not been able to find...
Hello,
I'm working on updating my copy of the nRF Connect SDK from 1.7.0 to 2.4.2. My project runs on an nRF9160 so I had SPM configured for my project and now I need to...
Hi I am working on a NCS v2.6.0 project that is using PSA Crypto to generate a keypair for each device. The keypair is being stored in persistent storage, but the issue I...
Hi Nordic Team,
My project goal is to send sensor data and audio stream from PDM mic over BLE from nRF5340 to another nRF5340 board.
For this I have split the project...
I am working on a new project which will use nRF Connect SDK 2.7.0. In that most of the code will be ported from legacy project that used IAR Embedded Workbench as IDE (Note...
Hello, I am building a Matter application (based on the lightning app) for the nRF7002-DK, and I would like to use part of the Matter SDK that is not included in the example...
Hello,
I have a custom board with an nRF9160 and is running mfw_nrf9160_1.3.5. The design is ready for production so I thought I will build 10 boards first as a pilot run...
I'm attempting to build the aes_gcm sample using NCS 2.4.2 for a custom board with an nRF9160. However, I can just build the project for the nrf9160dk_nrf9160_ns target since...
Dear person in charging,
I would like to know the nrf52833‘s RF power accuracy at the emission power of +8dBm, because it is described on the data sheet that the power accuracy...
Hello
I am new to the NRF Connect and NRF board development. I was trying to run a blinky code on the nrf 52840 dongle using the nrf52840dk. I was referencing the following...
I have a Matter over thread temperature sensor, and low energy consumption is very crucial for me. Therefore, I'm using the Nrf2.7.0 SDK ICD LIT KConfig options and I found...
