But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
In a legacy (nRF5SDK) application, we notice a parasitic' pin resets reported by the system (RESREASON).
As the device does not have an accessible reset pin,...
hi,
i'm learning on this exercise and COM 3 and 4 are busy with modem trace and terminal serial port so i try to print hello_world on VCOM1 - COM 9 port but it showing me...
I have installed nrfutil from PyPI using the instructions in section 2 of the nRF Util User Guide v 6.1.0. My main purpose for using nrfutil is to generate a DFU package....
Is it possible to use at least one channel of the TAMPC in a Zephyr application on the nRF54L15-DK? It appears that the channel 0 pins (p1.4 and p1.5) are used by the UART...
Hello Nordic Support,
I have a question regarding the real-time clock (RTC) functionality on the nRF9160.
RTC availability
Does the nRF9160 have an internal...
We are developing with Zephyr and the NRF54l15 and need to use a NAND flash IC (Macronix for example). But it looks like there isn't any NAND flash support.
Can you point...
Hello,
I noticed the DFU feature for the audio application is marked as experimental. Are there any caveats or gotcha's to be aware of before attempting to get DFU working...
the provider has provided source for their firmware which provides serial port communications to control operation only in old sdk 1.7.0 format
I need to use some other...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
When using SDK 2.6.x, I didn't know about Wi-Fi Credentials, so I connected to Wi-Fi as follows:
(Partially omitted)
With the release of SDK 3.1.1, I learned about Wi...
Hello, As part of an effort to migrate applications to nRF5415 devices, I've encountered voltage sensitivity issues when using existing sensors (bme688, bme280). After reviewing...
We have designed two custom boards based on the nRF52840.
Board #1 (Demo board) This board works correctly. It uses a standard 32.768 kHz passive crystal connected to XL1...
Is it possible to enable the Segger Flasher ARM Targer power supply using nRFutil?
We are now using a Segger Relay adapter , but this needs the Flasher's ARM target supply...
Looking for base examples for a push to talk using this dongle board and GATT. I choosed Peripheral LBS
Other basic example (Beacon, Blinky etc) compiled and work w/o problems...
Hi,
We want to set the PMIC's battery discharge limit via the registers BCHISETDISCHARGEMSB and BCHISETDISCHARGELSB to 1200mA but the nPM1300 PS does not describe how to...
