We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I would need to change the GPIO voltage of the nRF9161 (M1) from 1.8 to 3.0 VDC. On nRF9161-DK schematic I see that VDD_GPIO can be isolated from nPM1300 (U9) VOUT1 by cutting...
Hi Nordic,
I am currently working with the nRF5340 and trying to understand the process of building applications in a multi-core setup.
From both the forum and official...
Hi, We are getting packets a count mismatch error immediately after first successful bt_iso_chan_send() call, preventing ISO communication that worked in 3.0.2. This is our...
Hello,
I'm currently using Visual Studio Code with the newest SDK, Toolchain and Plugin on MacOS and most of my applications are freestanding applications.
Now I want...
Wireless Communication Synchronization System Based on the Alignment Principle
A year ago, I proposed the wireless communication synchronization system described below....
I am going through Lesson 9 of the nRF Connect SDK Intermediate course to understand how DFU and FOTA work in the SDK. I am using toolchain and SDK v3.1.0, and nRF Connect...
Testing a new nRF9151 device using a project derived from the Nordic "HTTPS client" sample project. We are experiencing a "Modem has crashed" event intermittently when running...
Hi，
Background Information:
Our product, BLE near-infrared device , is undergoing CRA (Cyber Resilience Act) compliance assessment—specifically for the EU RED Cybersecurity...
This seems like a silly issue, but I cannot get the UART output from the nRF9151 DK. Attached is a project that outputs via both LOG and printk() to a Segger RTT viewer without...
Hello,
I am working on a simple Bluetooth Mesh application for light control.
I started from the provided samples: - github.com/.../light - github.com/.../light_switch...
I am trying to program an external board using the development kid following the instructions HERE .
I am using the debug out P20.
I have tried supplying the board frm...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
i built a small breakout board for npm1300 (QEAAD0 2516AA) to experiment with it. the twi pins are wired to the i2c ports of a raspberry pi 4 to control it, and i have attached...
I do measure different values for source and ampere mode. On the nRF52 DK. Source Mode: disconnect SB9, Power Switch is off. Vout from PPK2 connected to nRF current measurement...
