We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
I'm leveraging the ble_app_cli example program for my project. The primary reason for this is that I need BLE and I need to be able store and retrieve log data which...
I'm downloading a firmware image from AWS via cell onto the nRF9160. I want to perform a serial DFU over UART. The DFU target is the nRF52840. Are there any existing samples...
Hello DevZone,
I want to send a simple AT-Command like: AT\r\n from the ESP32 to the Fanstel BC805M (nRF52805M) breakout board.
Problem : The Esp32 does not get a...
When handling a `BLE_GATTS_EVT_WRITE` from a queued write, the write event has the characteristic handle set to zero. How can I identify what characteristic is being written...
Hey there!
I'm new in the development with the nrf9160dk. And I wanted to connect the Murata SCL3300 digital inclinometer to the development kit via the SPI lines. However...
It's been a while since this Java developer really understood EE concepts.
Could someone jog my skills and explain to me roughly what the different pin rive modes are,...
Hi,
I need to send custom messages to models on my devices and I need to use a vendor model like I've seen other people on this forum use. But when I load the nRF Mesh...
Hello,
We are interfaced the nrf52811 with LSM6DSO32 through i2c and LSM6DSO32 is connected to Auxiliary(Temperature MAX30208) sensor through mode 2 connection. here I am...
I am trying to learn to use the nrfx API to control the nrf5340.
My installation is the NCS 1.6.0 with SES on OSX
It seems like nrfx most of the API devices are supported...
I'm trying to find a battery for my application and I need to know the max (peak) current draw for the nRF9160. On page 63 of the user guide, the max is 435mA with the specs...
I have a function which writes data to the external flash which is using a FAT file-system further using block device implementation of the SDK. Whenever I am calling the...
Hello,
I am working on nrf5340DK board and with a sample example "central_uart" under ncs->nrf->samples->bluetooth & "peripheral_uart" from ncs v1.5.1. I wanted to send...
Hello,
I am trying to setup test environment using nRF9160DK(PCA10090, 1.0.0)
Dev kit is located in Montreal, Canada.
I started with nRF9160_DK_Getting_Started_Guide...
I am trying to update the bootloader using BLE DFU and it does not seem like the app is launching after the bootloader update.
I currently have an app that works with the...
