But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
I working on a project that need to communicate with other mcu by SPI, the communication is work, but I have question about the start and stop of communication.
...
Hi,
I just met some difficulties to implant more then one service into my project. The project was developed based on hid_keyboard.
The project can work normally when...
I am using 2 nrf52832 boards to talk to each other through UART. One is programmed to the central SDK example and other other is peripheral. In the code, i incorporated 2...
Hi, I got the issuse about the connection with nRF52810. I used nRF connect to connect the nRF52810 device via Android,but it isn't easy to connect successfully.The nRF log...
Hello,
I have a question about the nRF52840 device and the supporting documentation. I am trying to figure out the current ratings for the GPIO. On page 198 it states that...
Hello,
I have an issue with the function sd_flash_write which ends up in a hardfault when returning to the function calling it. I know there are many Q/A on hardfaults...
Hi,
I have some questions about UART:
Currently I am developing software on our PCB with nRF51822 chip. When I was implementing and testing software on the Development...
Hi,
I am a beginner to BLE. I am using the nRF52 DK and i want to try out the advertisement and connection features.
I basically want to know how to send out an advertisement...
HI
when I use nrfutil.exe to generate .zip file on win10 64bit, I got the UnicodeDecodeError.
And :
Python version 2.7.9 (default, Dec 10 2014, 12:28:03) [MSC v.1500...
In my current project, I am receiving multiple indications from peripheral device. After 25 indications, I need to pause the indications or disable the indications. I am using...
I have a question about "LE Secure Connections (LE Security Mode 1: Level 4)".
I recognize that it is impossible to realize "LE Security Mode 1: Level 4" when adopting ...
I want to realize "LE Security Mode 1: Level 4". However, there is no IO capability in both devices.
I tried the following. 1) Set the IO capability of both devices to ...
I have a question about "LE Secure Connections".
I recognize that "LE Secure Connections" includes the following security modes and levels:
・ LE Security Mode 1 Level...
I run eraseall but the following error shows up. how can I fix it?
nrfjprog -f nrf52 --eraseall --log ERROR: JLinkARM DLL reported an error. Try again. If error condition...
Hi,
We have a requirement of reading the BLE Advertising name from flash instead of predefining it in as a MACRO. I saw in the notes it says to use ble_gap_cfg_device_name_t...
