But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello,
is there any kind of good practice available about how to generate UDP traffic with the nRF9160DK via NB-IoT for a simple test?
As far as I know the AT client...
Hi
I followed below tutorial with my nrf52840 using SDK 15.3.0
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a...
Here is the software: https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE which notably doesn't support the nRF52 dongle
I also...
SDK15.3
nRF52840
S140 v6.1.1
Q1. I have an RTC compare event connected to a Timer count task over PPI. The Timer is configured in low power counter mode. My question...
Hi, I am strugling to get the power comsumption down to the number I have been reading on this forum. I followed the instruction of the dev kit manual . When measuring the...
Hi, I'm getting regular crashes with my app: SOFTDEVICE: ASSERTION FAILED. Using and NRF52832, SDK 15.3.0, SD 132 6.1.1, and Mesh SDK 3.1.0. With DEBUG defined, I don't really...
I'm trying to interface 2 SPH0645 mics to the nRF52840 DK.
Little did I know when I bought them (the mics) that you need to waste 2 timers + 2 pins + memory space to make...
Hi,
I am trying to measure a signal using the SAADC driver on SDK 13. I have used the example from the nrf52 playground for low power ADC
I have a few questions on best...
Hi,
I have a nRF91 development kit and want to connect P4 to the Segger Jtrace for ETM streaming. In the manual, it stated that a 2×10 pin 1.27 mm pitch surface mount connector...
Hi,
Is there any way to get network time without previously setting it with AT+CCLK?
I would like to implement sort of "fake time" by initialising it with the network...
Hi, I'm struggeling with this stage on the "getting started assistant"
"Clone the nRF Connect SDK"
Is there any step by step video to help me do this, I have probably...
I have one service with multiple characteristics(11). Out of 11 characteristics I have 7 characteristics which have notify as their attributes. So when I select the notification...
I have been using nRF9160: LTE Sensor Gateway to send data from nRF52832 to the cloud. The nRF9160 is subscribed to nRF52832 and hence gets updates after every certain period...
Hi,
I'm trying to use Power Profiler Kit (PPK) with nRF52 DK to measure the power consumption of our custom hardware. My setup is as described below: - The PPK is connected...
SDK:15.2
IC:NRF52840
Hi，When I upgraded the device using usb dfu, after entering the app, there will be an additional current of about 180uA（Sometimes appear）.
Both...
