Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
We are in the final stages of development and are trying to tune our device to perform its best in noisy environments:
We are using nRF52833 SOC as a central...
Hello,
We are using 2 nRF5340-based devices running:
samples/bluetooth/periodic_adv_rsp
samples/bluetooth/periodic_sync_rsp
with the PAwR configuration (modified...
I am evaluating the board nrf3054-dk + nrf7002-ek I build and run the sample project net/samples/wifi/shell on my board when I compiled the project, I added the following...
The blinky example from the official website can be programmed, but after opening the code and compiling with SES to generate the hex file, it cannot be programmed. An MBR...
I think variations on this question have been posted before but they all seem to be very old. I'd like to use the Bluetooth 5.2 LE Power Control features that involve exchanges...
I am evaluating the board nrf3054-dk + nrf7002-ek I build and run the sample project net/samples/wifi/shell on my board I tested the wifi shell with some personal encryptions...
Hi!
I just upgraded a product we developed using a Fanstel BT840X module (nrf52840 with a Skyworks SKY66112 amplifier) from SDK 2.3.0 to SDK 3.1.1 and I noticed that our...
I'm planning on using an e-ink display with my custom PCB . But when I add/enable the e-ink display node in my device tree, the TF-M code throws an exception in /ncs/v3.2...
Hi,
The attached screenshot shows a section of an air-trace for the 5340 running a commercial LE Audio stack. From the rising edge of the logic inputs, it can be seen that...
Hi List, I am using ZMS to log data. While performing stress tests, I see few issues:
Including zms in the projects makes the application boot time delayed. The delay...
Hi there,
Several examples of the course include a configuration file and an overlay file for the nRF52840 dongle. However, the code cannot be compiled. The problem seems...
Hi everyone,
I’m trying to use the HTTP client sample from NCS v3.0.2 with a W5500 Ethernet shield on an nRF5340. DHCP works fine, and I can successfully POST and GET using...
We are using the Murata Type 2FR dev kit - https://www.murata.com/en-us/products/connectivitymodule/wi-fi-bluetooth/overview/lineup/type2fr
Internally, this has NXP's RW612...
I'm running the subrating sample (ncs\v3.1.1\nrf\samples\bluetooth\subrating) on two nRF54L15-DK boards. Using a protocol analyzer I'm seeing that when the subrate factor...
