After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
I would like to set up RTT on both net and app cores, but I haven't been able to get both running simultaneously. I'm wondering if this is even possible, and if so...
Hi, I am trying to get a working demo up for the Zephyr OS on your nRF52 DK but having trouble. See attached for description, I get this error -
-- runners.nrfjprog: Flashing...
Hi,
nrf9160dk device is not latching with CAT-M network. Please provide the solution for changing the "network mode" from CAT-NB(NB-IoT) to CAT-M in nrf9160dk device.
...
Hello,
I am able to program softdevice hex file with application hex file into nRF52840 microcontroller. However, I am not able to program softdevice and application hex...
Recently purchased nrf5340 to validate BT and BLE profiles.We have followed the guide and installed NRfConnect-3.7.0.
Installed BLE app and programmer app from nrfconnect...
I'm working with the latest v1.6.1 nrf SDK, and was able to get the Blinky sample code to work.. But trying to translate that to toggling other GPIO isn't working. I also...
I freshly installed Nordic Edition SES v5.50c and nrf sdk 1.6.1 on my machine and opened the empty_app_core with the Open nrf-sdk project option, selecting nrf5340dk_nrf5340_cpuappns...
While trying to build and run on my nRF9160 DK the project: asset_tracker , that I imported into SES by selecting: File>nRF Connect SDK Project...(in the SES menu), I followed...
Hello,
I have a ble nrf52840 module. I want to make it as becon code which is power optimized. Pls tell me the steps by which i can do that .Share some document or code...
hello ;
i need to send data from the nrf52840dk to / over the internet and to the server , so i know that on board nrf52840dk , there is no wifi chip on nrf52840dk , so...
Hi,
After the execution of erase all command(nrfjprog --eraseall) My custom board is not visible anymore. When I tried to connect with the nrf connect programmer ,I received...
This is the error I have. Couldn't figure out what causes this error. Tried all the related issues mentioned on this website. I have made sure the python and latest version...
The questions of data throughput:
1. nRF9160 supports SIM card for data transmission through NB-IOT, so what is the data transfer rate using NB-IOT?
2. Including data...
Hi, I am new to nrf.
l am using nRF5_SDK_15.3.0_59ac345
I am working on the ble_app_uart example and want to write the data in the flash of nrf52832.
I included flashwrite...
Dear Nordic Enginneer
Our customers has a problem when using the NRF52840.
They want to make a mouse,and now they use LLPM and then they use the gmouse example and the...
