I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
I am using the NRF9160 for SPI using an external Flash. After using the 'http_application_update' samples, I was able to get the value of the data written on the external...
Hi, I am a MCU developer searching BLE MCU to develop some IoT project.
I would combine nRF series and LTE NBIoT module for IOT project.
And I need to integrate many different...
Hello all,
I am trying to use my nRF52832 DK for a wireless camera shutter for my phone. I have reviewed the example code from SDK 15.3.0 named ble_app_hids_keyboard as...
Using SES, nrf52840DK, the onboard debugger.
I am able to set a breakpoint and use condition like x == 5.
I am unable to use anything but the == operator. In SES I...
On line 904 of nrf_log_frontend.c there is a log message to indicate the backends are flushed – but this message adds a log to the queue. If auto flush is enabled, this can...
Hi forum,
I am worked on nrf52832 using sdk 15.0.0.
How to used RTS and cts for enable HWFC on nrf52832.
Is their any example for HWFC control through RTS and CTS line...
Hi Devzone,
I use Thingy91. On the nrf9160 side, I run mqtt_simple example; on the nrf52840, I run connectivity_bridge with BLE feature.
When I send "900" via nus service...
I want to control two RGB LED strips with I2S with different GPIO. Not able to figure out how to achieve it. While trying to initialize by separate buffers and data handler...
Hi there,
I have successfully programmed the nrf24le1 on the radio module using the nrf6700 (motherboard) through nrfgo studio. I did so by plugging the radio module into...
Hello,
Is the Power Profiler App capable of calculating and outputting the cumulative energy output to the device under test (when in Source meter mode)? I am using the...
Hi!
There is two things confusing to me about taking IQ samples in AoA application.
1. It is clear to me that that the time between switching of antennae (TSWITCHSPACING...
Hello,
I am using the Nordic SDK v1.5.0, the modem firmware is mfw_nrf9160_1.2.3 and the DK for the nRF9160
In our application, we are using AT commands to setup and control...
Hi,
There is a similar case:
High power consumption in sleep mode after using SAADC
But I am using the SAADC driver version 2.0 because the oversampling feature is only...
I have seen multiple posts about the nrf5340 that confuse me. Posts like this one say that the board/chip is not available yet, as of 4 days ago. But after looking through...
