i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi,
We want to work on BLE mesh topology using nordic nrf-833 boards. We want to implement mobile application in react native to support BLE mesh features. Please let us...
I was using nRF Connect (v3.6.1) to communicate to Segger J-link Base (version 11.0) but it failed. The error message was: ""Failed to setup device: No serial port available...
I want to develop a software that can restore the program after a power failure. I mean, if the device restart, I don't want it to execute from the beginning of the main function...
I made a serial bluetooth function but I want to use it in a form like printf.
Please tell me how to use it using bluetooth_send function.
bluetooth_send("gyroscope...
The reference design for the nRF5340DK uses 0201 components for the matching network.
Would it be acceptable to replace the 201 matching network components to 0402 parts...
Hello NRF,
I have a custom board with NRF52832, and exposed the SWDIO, SWDCLK, GND, VDD, RESET pins for programming the board through the NRF52-DK board.
I started with...
Dear Nordic,
I have some issue with SPI interface (MCU as master, BL654 as slave)
I can see correct signal from oscilloscope, and SPI mode and CLK is config correct...
hello,
i am using nrf52840 with sdk 15 and using ble_app_blinky example i want to advertise my device as i beacon(only mac address) without any name what i did until now...
We have generated a .hex file to be programmed to the external QSPI flash on the QSPI bus of an nRF5340, using the same MX25 part as used on the DVK (8MB/64Mbit) but with...
Hello Team,
Need urgent support for the nRF52840-DK.
I want to develop a program for the above mentioned kit for green power zigbee communication. This DK will communicate...
I was testing 9160 power consumption, the specifications says it is the minimum consumption current 7µA, but when I test on the DK board, the minimum current is 2ma, my test...
Greetings, I designed custom board using nRF52832 and sht20 temperature sensor. I defined sda and scl pin number of sht20 in pca board file (pin number 23 and 24). 4.7k pull...
Hello,
I want to test cold start performance of GPS on the nRF9160 DK using the gps example from the SDK. If I run the example unmodified from the sdk, get a fix, power...
Hello!
I am working on a project where we want over the air updates for the finished product. To make that possible I implemented the buttonless DFU and it is working great...
