Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
To flash a new firmware I always do the same thing.
Open NRF Connect
Open Bluetooth Low Energy
Click: Start Scanning
Click: Sort by signal strength
Choose the...
Hi,
As well know, nRF52832 have more then one SPI and TWI interface.
How can I use SPI and TWI interface in the same program? for example, use SPI-0 and TWI-1.
Thank...
I don't understand how the guide gets to the Open IDE button. I used the automated installer and it did not appear for me. The guide did not provide any instructions on how...
I see that in the 6.20.14.20 RXADDRESSES in Reference Manual I can enable multiple addresses in the same time, so is it possible for nrf52840 to listen on several addresses...
SENT protocol uses a 1-wire interface to transfer data using time intervals. To receive data you simply measure the time between pulses on the wire. The transmitter never...
When I use the BLE mouse example in the nRF5 SDK (17.0.2), it works on iOS (14). However, the report is divided into 3 parts. I would like to combine the mouse buttons, X...
We are developing a controller for an Electric vehicle charging station. Already developed and successfully running the firmware on ESP32 for which we had used platformio...
I am using this tutorial to write a custom service and I got to a point to add custom characteristics and got a few questions:
- I don't seem to find any characteristic...
nRF52832 nRF5 SDK V17.0.2 SoftDevice S132 V7.2.0
I am running the sample program ble_app_uart in the above environment, but sometimes I miss UART received data. Teraterm...
Hi,
I want to do a custom developpement (custom board) for my project.
I have copied to a folder on drive D/: the peripherial_uart sample, as well as the folder Board...
Hi
We are trying to configure Nordic UE (NRF9160) at our local setup. In order to flash software we performed following steps:
We used ' carrier_deploy_e7f4d5d4-f607...
Hi,
I am looking to design a nRF52833-CJAA (WCSP/ BGA package) board using 4-layer stack.
a) do you see any issue in doing that, vs. 6-layer stack used in nRF52833-DK...
Hey
We encounter problems with the modem not establishing a connection after rebooting the processor for a few times.
Issue:
Firmware is booting normally
Cellular...
It support send periodic advertising with CTE in ncs v1.6.0, but I found that the scanner can establish synchronization with only a tag that sends periodic advertising. But...
Hello fellow Nordic community,
Assume that a given Peripheral ( P) is advertising a BLE GAP signal which allows for multiple connections to be made.
In the vicinity to...
