Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello I am currently working with the android application that Nordic provides for the generic on off example for lights using bluetooth mesh. Everything goes fine , I have...
Based on nRF5_SDK_15.3.0_59ac345,
a. fds_stat(&stat), and stat.valid_records=8, It means that the records are written in
b. err = fds_record_find(WK_UDM_FDS_FILE, WK_UDM_FDS_REC_NAME...
Hello.
I'm running the nRF5 SDK's ATT_MTU throughput example.(nRF5 SDK v15.3.0, nRF52 DK(nRF52832))
The tester is running as a central or peripheral device.
How to operation...
Hi nordic moderator team,
I'd like for you to reopen this thread https://devzone.nordicsemi.com/f/nordic-q-a/51673/nrf52832-sd_ble_gatts_value_get-or-catching-ble_gatts_evt_rw_authorize_request...
Hi,
I am using APP UART for Communication with slave device, the data transmission between two devices like send a command and get the response,
while getting the response...
Hi,
I faced a problem while building my project. Please see screenshot below
I think I have already include all the files and everything compiled. But this error shows...
I am trying to run smart remote 3 on PCA10040/nRF52832.
I use gcc makefile to generate PCA63519-SR3_nRF52832_Shield firmware. SD firmware is downloaded by jflash and I use...
Hi,
I want to update firmware on nrf52832, but I have an error: DFU insufficient resources
I found this and this , so I try to program my softdevice with this file: /nRF5_SDK_15...
Hi，
there is a issue very strange, on a nrf52832 project, it use two gpio set to sense low level, one is p18, one is p29, I found there is no response for low level of p29...
We are using nRF52832 with SDK_15.3.0 running the Nordic UART service (NUS) example.
Out of the box we find that the uart event handler is continually being called with...
Hi,
I have an SPI peripheral on pins 26, 27, 28, 29 which I'm able to override the default system's UART0 pin assignments in nrf9160_pca10090ns.overlay. However when I enable...
Dear sir,
We have interfaced a charger ic with NRF52832. It is having a charging status pin to show completion of charge. It is having 3 states
1. High impedance (Battery...
Hello guys,
Something strange is happening here and I need your opinion about that... I have a custom board with nRF52840-based BL654 module on it. I am using SDK15.3.0...
Hello
I am using nrf52840 chip. I am having trouble configuring SAADC to read analogue input on two channels (one signal is VDD of the chip). I have already searched the...
