I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hello, I want to ask a question. We have a project that needs OTA function. There are two Bluetooth devices A and B.
1. Both A and B are central_and_peripheral
2. A's...
I want to check for an RX timeout after sending a TX.
I am puzzled on how this comes about.
As best I can tell I have enabled TIMER3 for the timeout.
I have created...
I'm trying to create a user defined HCI command for nrf52840 over the Zephyr APIs to be used against Bluez stack on Linux.
I've enabled the CONFIG_BT_HCI_VS_EVT_USER=y....
Hello,
I am trying to accomplish sending a simple ON or OFF command to the coordinator. Is this possible to do?
I have a router device with these Clusters:
It...
I have been converting my TWI calls to be asynchronous by specifying a twi_handler, but my NRF52840 does not sleep during the TWI calls.
I use SDK15.3 and s140 softdevice...
So this is my understanding of the programming process of an external board using the DK.
Pins from table 1 here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk...
Hi,
I want to develop DFU using BLE. I have started with test image given in the example folder.
I have nrf52480 device , using S140 softdevice. I have followed these...
I am unable to see advertisement on the nrfconnect app, when using BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED
However, when using BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as a central and Android device (Bluetooth 4.2) as an advertisement.
During development, I was wondering...
Greetings.
We've been developing a product that uses BLE Mesh. We are currently using the Waveshare nRF52840 Bluetooth 5.0 Evaluation Kit for prototyping purposes. As far...
When I try basic usage of NRF Queue library I'm getting the following error:
Undefined reference to `nrf_queue_write'
SDK version is 15.3.0.
In sdk_config.h I've enabled...
Hi Support,
I have tried setting up my nRF52840 Dongle ( https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF52840-Dongle ) PCA10059 as explained in the steps...
Hi,
I've got the gaming mouse dev kit and I'm stuck trying to get it programmed using my nRF52840-DK. See my hardware connection image below.
If I leave the mouse power...
Hi. I am currently using a custom nRF52840 board.
I am able to connect and pair with both IOS and android via BLE. However, the IOS have some issues.
After 45 minutes...
