I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hi,
I a\m looking for your recommendation on screen to use with nRFLM20DK board to experiment with LVGL display. Assuming that latest version of nRF Connect SDK has everything...
Hi,
I am using nRF5340 (CPUAPP) with MCUboot and Partition Manager (pm_static.yml, CONFIG_PARTITION_MANAGER_ENABLED=y ).
Build and flash are successful, but during debug...
Dear Technical Support Team,
I have recently been developing with the nRF54L15-DK development board, using the official channel_sounding/cs_test example provided by Nordic...
I am designing a battery system with can charge or supply power via a USB-C PD controller. It will operate up to 20V. I want the option to connect this USB-C D+/D- to the...
Hello, I was able to flash the firmware built using the samples provided by the "nrf connect sdk" using VScode. But, I see failure when I tried to program the nRF54L15 with...
When the USB stack and your local Filesystem code both try to control the flash chip simultaneously, the system will crash or trigger a HardFault, causing the restart.
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
I was trying to flash a program on nRF52833 development kit and got this error, it important to notice that my college was trying to flash (via VS code) it before and I am...
Hi,
I'm working with the nRF54LM20 DK (nRF54LM20A) and evaluating whether it can act as a USB host to read data from an external USB CDC ACM device.
The intended setup...
Hi
I remember the Devzonw could ask for hardware instructions. My matching circuir has used the nRF54L15 reference design and nRF21540 DK design, all the value is the same...
I used binwalk to analyze the zephyr.signed.encrypted.bin file generated by the routine mcuboot_with_encryption. I found that the firmware was not encrypted but merely compressed...
We have a peripheral device that maintains a PAwR sync (as a syncer/responder), connects to another peripheral in a central role, and also accepts connections from a central...
I tried writing read and write code for sEMMC based on information obtained from an AI assistant. The resulting code is shown below:
As you can see, the block address...
I used an oscilloscope to check the waveform and found that only the clock and IO0 had waveforms. I am using this interface to send data:
nrfx_err_t nrfx_qspi_write (...
