Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I'm writing an application for the nrf5340 with nrfConnect v1.6.1,
I've been able to do the FOTA upgrade through BLE with the example smp_srv located inside zephyr/samples...
I recently got the nRF52840DK and have been able to build/flash a couple simple samples. However when attempting to try the OpenThread CLI example on tool chain v1.6.1 and...
Hi,
cannot run pc-nrfconnect-launcher v3.7.1, built from sources.
```
$node -v
v12.22.5
$git clone https://github.com/NordicSemiconductor/pc-nrfconnect-launcher...
Hi,
When I want use nrfjprog to program my NRF52, I have a problem.
This why I write to program my nerf : nrfjprog -f nrf52 --program _build/astronaut.hex --sectorerase...
Hello,
Is there example code on how to get NRF_SAADC_INPUT_VDDHDIV5 working? When I do nrfx_saadc_init(), I get NRF_ERROR_INVALID_STATE.
Same code works fine with normal...
I am using nrf5340 and icm20948 for our development. i had initialized things as shown in code attached.
this work fine for me. but when i am uncommenting rc |= inv_icm20948_enable_sensor...
Is there any guidance on zigBee OTA? What are the similarities and differences between ZigBee OTA and BLE OTA? Could you please tell me what I need to pay attention to during...
Today I received my first CMSIS-DAP debug probe (Pitaya link) and tried to integrate it into my development environment. Unfortunately, I must have broken my Pitaya Go (Nordic...
Hello,
I've been very slowly gearing up towards developing for the nRF9160. I'm going through the "nRF Connect SDK Tutorial"
https://devzone.nordicsemi.com/nordic/cellular...
For example, I'd like to add at_cmd_parser to my project. It's under /ncs/nrf/lib/at_cmd_parser.
My project is out-of-tree in its own directory. Initially I tried add to...
Hello,
I am using example code of LIS2DH ac celerometer sensor with nRF SDK v1.3.1. Building the example code I am getting macro error in devicetree.h file as mentioned...
Hello,
I am using PPK 1 kit with nRF52 DK. The system is used to measure the power on nRF52840 DK using DUT mode. The system was working just fine until I started receiving...
Hi
I'm trying to use the nrfx TWI Slave function with IRQ (No Poll), but there is no clean code available I found.
I'm using the following code:
But even if I can...
Hello,
I am using NRF9160 running the Serial LTE Modem application in NCS 1.5.0. When connecting with AWS IoT over a secure MQTT connection the maximum MQTT packet size...
I'm using nRF5340 to provide Bluetooth connection to other devices. Almost all Android devices connect correctly, for example: Samsung S21, LG G8X, Xiaomi Mi Mix 2. However...
