Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I'm studying with PCA10059,trying to build a gateway between BLE peripherals & PC.
For PCA10059 has build-in USB socket,and I will plug them into PC's USB ports at last...
Hi all,
I want to use UART periodically, but because I need to communicate with other standard UART, I cannot use LPUART
I saw that Zephyr's demos all use CONF_SERIAL...
I am following all the steps given here: nRF Sniffer for 802.15.4 but my zigbee sniffer did not show up. When i did the steps given there for ble sniffer it showed up. steps...
Hello,
I am new to developing with Nordic products and I have a question regarding the components in the antenna matching network. I am designing around the QIAA QFN-73...
Hi,
I am trying to use the nRF915-DK with a GNSS Tracker application. Everything works fine, but, I am not able to set the nRF9151-DK properly for utilizing the board...
Hello
I'm preparing the certification RF testing software on our product 4MOD9192 using nRF7001 for wifi function.
During the certification test process, we need to...
Is it possible to add custom regions for a project to be used by the Partition Manager? I see how and where regions are defined, as shown here , but I'd like to use multiple...
I have a nrf9151dk with a nrf7002ek shield. The nrf9151dk has the DECT NR+ PHY firmware running on the modem core.
I would like to do Wi-Fi positioning with the nrf9151dk...
Hello,
I am using the nRF52833 - DK and running the USB CDC ACM example. I can transmit and receive data with the example. I noticed that when receiving data I am only able...
I am using Zephyr 3.7.0 with the Nordic-provided low level link layer (LLL) code on an nRF52840-DK. I'd like to set a breakpoint on rp_comm_rx_decode() ( https://github.com...
I want to connect two nRF54L15 development boards using I2C protocol. Is there any sample in nordic SDK v2.0.8 or v2.0.9 that I will help me to set up nRF54L15 DK as a master...
Hello,
To preface:
HW: nRF9151DK
SDK/Toolchain: nRF Connect SDK v2.9.0
I am new to Zephyr (first project)
When using a nRF91 modem, it seems that CONFIG_POSIX_API...
Hi there,
I would like to get information regarding the possibility of implementing 5.1 isochronous audio streams on the nRF5340 Audio DK development kit. According to this...
I've been using the function nrf_ble_scan_filter_set for several years with developmental hardware based on the ble_uart_c example, so I've reviewed that example thoroughly...
