Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hi,
I want to measure the duration of a single pulse using GPIOTE , PPI and a Timer with a NRF52840.
My initial idea was to have two capture tasks for the GPIO events...
Hi There,
I try to develop an application in intermittent conditions, it will off work frequently as for lacking the energy.
I try to resume the application from the last...
Essentially the title. Given that I have a BLE device which I have configured to have Legacy DFU services, and also customized the DFU service's UUID, how would I go about...
Hi,
I have nrf9160-DK and I am using NCS v1.6.1. I am trying to run HR Peripheral sample application on the nRF9160DK board.
I have flashed nrf52840 with hci_lpuart sample...
I am trying to using nRF52833 and nRF52840 as a BLE central to connect customer's BLE peripheral.
The attached screenshot is the service discovered by nRF connect Android...
Hello,
I am developing an application based on the BLE examples from the nrf5 sdk using he Segger Embedded Studio.
I am porting a library for a peripheral component and...
https://devzone.nordicsemi.com/f/nordic-q-a/80125/want-to-achieve-1-2-mbps-through-ble
Issue is in this link is not properly addressed . I want to work on BLE with good...
How much i can apply maximum and minimum voltage at Analog pin of nRF52832 controller IC? And Please also guide me is there any mention in the nRF52832 Datasheet.
Hi all,
I am using SDK = 15, softdevice = v6, chipset:nrf52810
I have used ble_app_uart and SAADC example code for one of my application, its working fine, and next i...
Hello,
I'm using nRF v1.5.1 SDK.
If I have my RX buffer to be of size say 6, and I transmit 7 bytes then my code will detect a full RX Buffer and go to the endrx_isr...
Hello,
Looking at the errata entry [78] TIMER: High current consumption when using timer STOP task only , I see that it recommended to use TASKS_SHUTDOWN instead of TASKS_STOP...
Hi everyone,
what are the tolerances of the internal reference voltage of the ADC (0.6V) at room temperature? I know the tolerances are included in the gain error and are...
Hello,
I'm following this documentation Doc to include Fota upgrade on peripheral LBS sample but I have the following problems:
1) all file .bin like ( app_update.bin...
I'm using dongle nRF52840 to sniff packets between earphone & iPhone.
I am facing the same problem: " Encrypted packet decrypted incorrectly (bad MIC)"
just after LL_ENC_REQ...
HI,
I'm developing it using NRF52832.
I'm updating the remaining battery capacity using saadc. However, the battery value is not stable because the value obtained from...
