Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hello, I am interested on nordic devices that support: 1) 802.15.4 (eg. Openthread) 2) secure storage for storing keys (e.g LWM2M credentials) 3) zephyr - rtos
I have seen...
Hi, we have a nRF9160 DK where we have uploaded the AT_CLIENT example on. Have tested the board and it works fine, able to send AT Commands and join to the network etc......
Hi,
I want to store scene when long press one button and recall scene when short press. I have done some changes but not able to achieve it, i am not sure if i should...
I was looking at this compatibility matrix, for SD and SDK.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52832%2FCOMP%2Fnrf52832%2Fic_rev_sdk_sd_comp_matrix...
Greetings!
we are using nrf5340dk to communicate with a Nucleo shield that has LIS2DW12 accelerometer on it (shield is X-nucleo-IKS01A3). We have a problem communicating...
Hello, I'm beginner for nRF52.
I saw examples about entering DFU by button and buttonless.
Is it also possible that changing the boot mode by a gpio pin which controlled...
Hello all, I'm working on ADC and data transmission.
Device do ADC first, and send those values.
Sampling frequency of ADC is ~80 kHz (sampling per 13 microseconds), and...
Hello,
We are using nrf52805 for our project. Facing some errors like "GATT ERROR" and GATT INSUF AUTHORIZATION and GATT CONN TIMEOUT ERROR" when I want to upgrade my application...
Hi,
We are developing our product based on nrf52382. In the scope of the certification testing of our end product, the test laboratory asks me if the Bluetooth low energy...
I am currently building a dynamic multiprotocol application (Thread+Bluetooth LE) with the nRF Connect SDK. For tweaking coexistence I would like to limit the length (=duration...
Hi,
In nwp-036 page 7,here is the AOD sketch map as below :
As fat as I am concerned, the Transmitter and Receiver should be reverse ?
Or there is something I misinterpreting...
Hi,
Background: I am looking at interfacing nRF21540 (FEM) with nRF52833 (Host) - hoping there's Zephyr support available for this(?)
Question: Product spec for nRF21540...
I'm trying to find the address of an attached twi sensor by using the twi_scanner. It worked on the default pins
but when I change the pins like this
It simply doesn...
Dear Nordic team.
We have to add new sensors using I2C protocol on our previous project.
Can i configure WDIO and SWDCLK pin to I2C pin?
If possible, i will reuse my...
Hi,
I would use the test nRF9160DK and Thing91DK with CMW500 equipment under NB-IOT stanadard.
Both DK kit and Thing91DK can connected to service provider when I plug...
