I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm using nRF52840 and want to send a data of 200 bytes over BLE, but while adding the characteristic, if I give maximum length above 101 it does not accept it. Can someone...
I am working on a limited release project that has multiple devices which require programming. Part of the appeal of this device is its programmability so I am going to provide...
Hello,
I am looking for a low latency (end to end) wireless module for Joystick application and this is for a medical VR platform.
Latency requirement is <= 5ms.
Data...
Hi I'm new on zephyr
In my hardware the sensors around the soc are most of time not powered.
At Startup the OS initialise SPI, I2C, UART and some pins are set to 1....
Hi,
I am working on nrf52832, s132, SDK17, trying to trigger the saadc with the RTC2
This is my setup :
what I am trying to do is to periodically trigger a series...
I am using a custom board using the nRF52832. I have developed a number of applications using this board sucessfully using nRF5 SDK.,
I am porting a current application...
Project Zip:
Following is my setup:
Board : NRF52832 by Sparkfun( Link ) - Added pull-up resistor for TWI
Sensor: LIS2DH12(Custom breakout)
IDE: Segger Studio...
https://devzone.nordicsemi.com/f/nordic-q-a/79832/need-interface-mcu-initial-boot-firmware
apparently i can't update it anymore. does 'engineer assigned' mean that it can...
Hello,
I was measuring the current of a circuit I made using a PPK II and noticed I am getting two different readings from the two PCs I used (a work and a home PC).
Both...
hi
my first test do not run, bletooth is not enabled and could not get the bluetooth device led on board and signal on my mobile.
i following this link
https://infocenter...
Dear team,
i am working on ble_app_lbs_nus_c project when in this project try to add nrfx_timer.c file
we got an error like this.
and in sdk_config.h file is there ...
Hi,
I am receiving NRF9160 board. Please let me know if we need to change anything to support India Bands. Also it will be great if you can share Indian service provider...
How do I quickly check if the external crystal (32.768 with 15pf load caps.) I soldered is working.
I built a custom board but had to reflow solder in my lab.
Everything...
Dear DevZone community,
I'm developing a Mesh application using nRF52840 Segger Embedded Studio (SES) onLinux. I'm using version 5.0.0 of the Mesh SDK. As desccribed in...
