I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
After successful compilation of code the west flash command shows this output after using Tag connect to debug the icarus board with the nrf9160 development board. Normally...
Hi. I know this issue already point out by some of the developers. But I don't get the right way to generate a hex file for my client.
I select the Release on the top right...
When using the local timer of the SAADC it should be started with TASK_START according to https://infocenter.nordicsemi.com/topic/ps_nrf52840/saadc.html?cp=4_0_0_5_22_4#concept_continuous...
Hi there,
I'm interested in using LittleVGL (lvgl.io) for my project. There is a LittleVGL example using nRF52840 in Zephyr project, but no in the nRF Connect SDK. Are...
I have successfully implemented the meander PCB antenna outlined in this app note, however, I am looking for and cannot find information on a shrunken version of this antenna...
I am trying to create an AOA link sending a CTE from an nrf52811 (BM833A module) and the receiver with an nrf52833 (bl653 module). Analyzing the CTE detection data, the first...
Hello guys,
I've a PCA10040 connected to my laptop.
It works fine with all the .hex BLE template example in the nordic SDK except with the UART example.
After download...
Hello,
I was using the usbd_ble_uart code for the nrf52840 dongle. When I connected the dongle to u-link 2 debugger and used keil uVision I was just doing my settings in...
NCS version：v1.5.1
board：nRF5340DK(0.11.0)
first，i use SES Embedded open radio_test project and choose nrf5340dk_nrf5340_cpunet ,and use [west flash --erase] download...
I am using nRF Connect SDK Tutorial - Part 1 | NCS v1.4.0.
I am using MacOS and nRF Connect SDK v1.6.1 .
a. The JlinkExe executes but JLinkRTTClientExe doesn't show any...
As noted in recent past cases, we have an issue with the state of the nRESET pin that is causing unwanted resets when connected/disconnected from external hardware (programmer...
I used NRF52840 Base on NRF SDK15.3 and freertos.
I have two task call nrf_crypto_aes_crypt a t the same time occasionally return NRF_ERROR_CRYPTO_BUSY. And also I add mutex...
Hi
I am developing with nrf52832 development board and sdk17. I'm trying to communicate with redpine rs9116w through spi but get some problems.
I have an other nrf52840...
