Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I am porting my code from Nordic SDK16 to Zephyr and NRF Connect SDK 2.0. I am working on putting a chip into sleep mode and set up a wake up on a press of the button. Everything...
Hello,
I am working through the Zephyr training modules (These are great, thanks!) and encountered an issue I do not know how to resolve. This issue applies to general debugging...
I'm using SDK17.0.2
I need to keep a noinit variable in memory so that I have the correct flag when I execute the DFU. So I use the following method, but it doesn't seem...
I am on nRF52840, and ANCS can get the app name. After switching to nRF52832, you cannot get the app name. The driver of the two chip ANCS is the same, but the Bluetooth protocol...
Hello,
NRF SDK version 2.6.2, tested on 2.8.0 as well
Hardware: NRF7002DK
Sample: Wi-Fi Monitor
When changing Wi-Fi channel using following function
ret = net_mgmt...
We have developed a custom board with an external 32 MHz Crystal but I am having trouble initializing everything correctly. With the Zephyr "Hello World" example code I can...
I want to do BLE FOTA with my customborad, so I have added some configs of FOTA to my developping project.
those configs are referenced ”DevAcademy” Exercise 3 - FOTA over...
I been trying to figure this out but to no avail. I get these errors on build.
:/ncs/toolchains/b620d30767/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi...
Using the "launcher" the open button appears to do nothing and the update from V4.2.0 to V4.2.1 produces an error message.
Twice I have uninstalled V5.1.0 and replaced it...
I'm using an nfr52840 board.
I noticed that when using The 'zephry-sdk' v3.5.99-ncs1-1, when doing a passive scan using:
BT_LE_SCAN_ PASSIVE
which sets:
BT_LE_SCAN_PARAM...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message with a something hits the device. To achieve this...
To output PWM signal as early as possible after powering on the NRF5340DK, I added the same code in mcuboot/boot/zephy/main.c and mcuboot.overlay as in the app core. This...
I reference the sample at https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise-3-interfacing...
