Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I am using the npm2100 as a power management chip in my product, utilizing only the boost function. When only the npm2100 is soldered on the PCB with no load connected...
I am using nPM1300 MIKROE Click with ESP32 over I2C and enter ship mode by writing the required I2C registers from ESP32 .
Observed Behavior
Ship mode command is sent...
Hi,
I am developing a feature to add remote provisioning support to a BLE Mesh-based network. In the network, a provisioner node receives, via a serial command, the UUID...
Hello,
I am trying to reduce the current on the nRF5340 during the distance measurement (dm) sample for BLE ranging. For current measurement I am using the Power Profiler...
I've been trying to establish the network using Open Thread API.
After enabling the IPv6 by using otIp6IsEnabled , when try to start the joiner using otJoinerStart but it...
Hi,
I've already spent a lot of time on this issue. I develop on a Windows laptop. I need to run unit tests with Twister before committing to our repository. I can't do...
We are using SDK 3.1.1 and nrf52DK with our own Model ID and anti-spoofing key from Google.
When flashing the Locator Tag example to the board, a half sheet notification...
We are developing a battery-powered medical device using nRF9151 with nRF Connect SDK v2.9.0 , where data is transmitted to AWS IoT Core using MQTT over LTE Cat-M . While...
Hey, I'm looking for a solution to encypt the DFU_Application.zip and that the nrf52840 MCU can encrpyt it at runtime. Actually I've read that this not offical supported of...
I’m working on an indoor tracking system based on the Bluetooth LE Channel Sounding (CS) API. My target is to support multiple initiators connected to a single reflector,...
I'm using the DFU bootloader from the nRF5 SDK 15.0.0. To initialise the DFU service from the application the ble_dfu_buttonless_async_svci_init() function from the nRF5 SDK...
Hi,
We're about to make a bunch more of our custom boards based on the nrf5340_audio_dk platform (modified with a stereo codec and some other stuff) with a modified version...
Hello, as the title suggests. I'm just wondering if the nRF91 (nRF9160 or nRF9151 DK) can use vanilla Zephyr instead of NCS for getting GNSS data (using the GNSS API)?
I...
I am using a STM32 with the NPMX drivers.
I am having a few issues and wanted to see if there are recommendations.
Issue 1:
disabling the interrupts does not seem...
