This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Dear Nordic Team!
We are struggling with a fatal error occurring during boot phase before entering the application main. When setting the baud rate of UART2 to 38400 or...
Hi,
Two month ago I have test nRF21540 and nRF54L15, they cannot word with each other.
However, I notice these days updated with
https://docs.nordicsemi.com/bundle...
Hello,
I am trying to use the nRF21540 in nRF54L15, I notice document metion
I am wondering what is the difference between PPIB and DPPIC. What does appropriate...
hello, I encountered a problem using SPIS to communicate on nrf54l15
Environment: NRF54L15, NCS2.8.0
When using SPIS for SPI communication, you must first write empty...
We are using nRF Connect SDK 2.9.1, Zephyr. The hardware used is a nrf52840dk, rev2.
We have a proprietary protocol that is running concurrently with BLE and uses MPSL API...
Hi everyone
I am using the nRF9160 DK board with the VS nRF Connect extension. I am stuck at lesson 7 exercise 1 of the Cellular IoT Fundamentals lesson.
Up to this lesson...
hi support team,
i want running chat demo in mesh fold in ncs2.9.0, but it doesn't support thingy53 natively. so i ported some of the file from light to chat demo. you can...
Hi everybody,
I'm writing because I'd like to check if I understand the functionality of the AT command AT%XBANDLOCK correctly.
The first part of the question should...
Hi! I have been developing a GATTClient and GATTServer on two separate nrf52840dk boards and have been doing so for a long time.
This Friday I got everything to work when...
Hi Nordic Team,
I'm currently working on a BLE project using NCS v2.9 and targeting a custom board based on the nRF54L15. My goal is to use the SYNTH LFCLK source (instead...
Hi Nordic Team,
I'm facing an issue with BLE communication on my custom board using NCS v2.9. I started from one of the standard SDK examples (like throughput or peripheral...
Hi,
I just got a PPK2, I'm going to measure the current of a nrf52 custom board, which is supply with Li-ion battery.
Should I connect GND on PPK2 to battery(-) when I...
Hello,
I am debugging in an environment using BLE with nRF54, but after breaking, when I step through it, the debugger stops and I am having trouble.
The environment...
Hi Nordic team,
I'm working with the nrf5340_audio source code from the nRF Connect SDK and have compiled the project as a gateway. When I try to connect to a headset, I...
