Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hello everyone,
I have some questions regarding the registers of the nPM1300 specifically for the load switches and LDOs.
In the data sheet in chapter 6.5 under "Load...
Dear Nordic team.
I am a beginner learning to connect a SPI devices with nRF54L15-DK but the program always reports errors. Here are my related codes:
nrf54l15dk_nrf54l15_cpuapp...
NCS SDK and toolchain: nRF Connect SDK v3.0.2
Boards: nRF52DK-nRF52832 , nRF54L15DK-nRF54L15
Issue:
After un-initializing and then re-initializing MPSL, MPSL no longer...
Hi,
We are using the nRF Device Manager app (Android) to update firmware over BLE to the nRF54L15 DK, and it was working fine until August 26, 2025, when the app was updated...
Hello, I followed the "DFU over UART" exercise of the intermediate lesson 9, and I have problems with launching the main application. I'm using nRF54L15-DK board, SDK v3.1...
Hello.
I'm currently migrating our existing application code to the NCS 3.1.0 SDK. As far as I have recognized, with sysbuild the child image build has been replaced. We...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hi, i am trying to onboard our custom board using a nrf9160 to nRF Cloud using this guide: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/nrf_cloud_multi_service...
Hi we are developing a prototype with NRF5340DK, for which we needed to control few set of GPIOs. we wrote our code in the assumption that it's pretty straight forward and...
Hi,
I just updated my vsCode extension and the visual devicetree editor stopped working
I can compile just fine but changing the DT will prove difficult from now on. ...
I used the official example provided by Nordic: github.com/.../nrf70-wifi-ble-image-transfer-demo . I followed all the instructions to complete the preliminary configuration...
1. can you tell in detail about Easy DMA supporting on SPI, I would like to understand how I can utilize DMA feature for communication with RAM over SPI what is the added...
Hi
We have nPM1300 evaluation kit, we use SW1 VOUT1 1.8V as VINLDO1 input, we remove jumper JP7(for LS_LDO_OUT1 connect to R8) on P15 connector, and provide 1kohm loading...
We just started a project to replace an old PAN1720 and decided to use the nRF54L15 based module. So I am just getting started with the VS code and zephry enviroment using...
The UART (Port 2) gets garbled after bt_enable(). This issue does not occur if actively Debugging using Segger.
The issue is also reproducible upon a settings_save_one(...
