When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I am trying to evaluate the asset_tracker_v2 on the thingy91, and its low-power items.
Perhaps I am missing something, but changing the config in the cloud seems to...
Hi,
I try sdk 17.02 nRF52840 usb audio demo, I want to achieve 48KHz stereo music play by a I2S DAC.
Because I need to compress data in main while(1) loop, I found that...
Hi,
I'm little confused regarding BLE NUS and characteristics.
I know that the characteristics are used to expose data, but we also have BLE nus which is used to send...
Hello,
I have 2 questions:
1. Could you tell me the current consumption of a nRF52832 running RTC with external 32 kHz crystal and no RAM retention? Is it 1.9 µA?
...
Hello,
I use nrf52840-dk as central_hr and nrf52833-dk as peripheral_hr, examples from NRF Connect SDK.
It works well, but I want to implement reading Device Information...
I got following error when use the Command Prompt feature
After i run "ncsmgr init-ncs" from bash, it shows
$ ncsmgr init-ncs Checking out NCS v1.6.0 ...FATAL ERROR...
Hi,
I'm developing with 52840 DK, trying to add peer manager to another project I've modified from ble_app_uart (basically I've added saadc, SPI, USB and I2C module based...
Hello
I was setting up the nordic thing 91 (1.4.0, 2020.23) using this video https://www.youtube.com/watch?v=xQ7hDzRULJQ&ab_channel=NordicSemiconductor .
Things were...
I'm starting to design a custom board around the NRF52820 using a 3.7v battery and there is no reference circuity for VDDH using Battery/Ext. regulator. Any tips on what I...
Hi,
We are in the process of evaluating coded phy transceiver for our next product. The product is a IoT node which will send sensor data to centralized gateway and will...
I am using nrf_drv_twi_rx to initiate an I2C read transfer but the interrupt isn't fired for the RX transfer when the ulTaskNotifyTake is used, but seems to work without ulTaskNotifyTake...
Hello, I am making a system with 20 peripherals to a central base on nRF52840. I followed the firmware."ble_app_uart__saadc_timer_driven__scan_mode" from NORDIC playground...
Hello, i I am designing a prototype, the goal is to be able to control a small engine. This engine will be activated when a message is received in MQTT. I currently succeeded...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. I have now two questions: - is ZigBee 3.0 supported by...
