I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I am using the nRF52840 and the nRF Connect desktop.
the nRF52840 serial number could be recognized like this.
the nRF connect BLE and programmer like this.
what...
Hi,
I tried to run the code which was used by another forum user:
https://devzone.nordicsemi.com/f/nordic-q-a/63149/nrf5340---p0-10-not-working-as-spim-miso-on-non-secure...
Hi, everyone
I am developing a BLE product with NRF52840 base on SDK 15.2.
Due to the cost of the product, we are now evaluating the feasibility of migrating from NRF52840...
Hi,
I am testing curve25519 in M52810.
The following is snippet.
nrf_crypto_ecc_curve25519_private_key_t bob_private_key; nrf_crypto_ecc_curve25519_public_key_t bob_public_key;...
Hi Dev Team,
I had a task to work on that required a timsetamp to schedule a certain event, like for example I wanted my modem to start off every morning at 10:00:00 and...
Hi,
I am using Thingy 52 to measure the acceleration from accelerometer. I was expecting values like m/s2 but I am seeing values in unit vector, ie, values between (0 -...
I have nrf52dk (nrf52832) board and a custom nrf52805 board. The nrf52805 board has no external 32kHz crystals, but only 32MHz crystal. Also, it is in LDO mode (no DC-DC inductors...
Device nrf52832, nrf5_SDK_for_Mesh_v3.2.0_src with nRF5_SDK_15.3.0_59ac345
Hello.
I want to transmit and receive some data between smartphone app and mesh sensor.(almost...
Hi, Im using nRF52840 DK, Segger Studio v4.52 and SDK version 17. I have been trying to make BLE OTA DFU work but have had many problems along the way. I followed the guides...
Hi folks,
I need a production test of an nRF52840 module at PCB level. Our board connects near instantly with nRF Connect + Bluetooth Low Energy, and displays its device...
Hi,
I am trying to implement wireless power transmission. For sending output voltage information from receiver board
to transmitter board continuously which of you module...
Hi, I am getting link time error in segger when i building a pre-built library with zephyr for NRF5340.
Error says,
c:/gnuarmemb/bin/../lib/gcc/arm-none-eabi/8.3.1/.....
HI. I have modified "usbd_ble_uart" a little bit and have changed the BLE service for transfering the received data from USB over BLE. The problen is now, the BLE service...
