Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I'm trying to update our LTE connection library to use the LwM2M Carrier library to be prepared for carrier certification and I am not seeing any way to request that the modem...
1.Project only has one main.c file. Other files are in zephery public folders,like conn.c etc.
My problem is ,if I modified conn.c for one project, how about the other project...
Hi, I've recently been diving into the whole trustzone implementation on Zephyr and I'm having trouble understanding how to properly work with it.
My question is fairly...
I'm using the default implementation of the Peer Manager module. I see under the hood it uses the FDS module to handle Flash Write/Reads. If I wanted to implement some Flash...
Good evening,
I am using a nrf52840DK to set up a product prototype and I have a couple of questions about the peripherals. My nRF Connect SDK version is 1.5.99.
1....
Hi, Iam working on creating a ble mesh network. I wanted send led status whether on/off message from server to client periodically like every 10sec. I have configured the...
Hi I'm learning Zephyr ecosystem in context of using nRF SoCs. How one can achieve current consumption values as low as in datasheet ( 0,4 uA in System Off, with no RAM retention...
After nrf52840 uses the SPIM3 peripheral to send data, turn off the SPIM3 peripheral to enter low power consumption, and there will be 700UA current; if the SPIM3 peripheral...
I am trying to read data from a chip over SPI.
The implementation of the SPI comms is not ideal as they require a new CS/SS line toggle on every byte. I cannot do a bulk...
I hope that someone can show a clear example of this. I surprised that it isn't in the SDK examples. Basically, it is necessary to stop the BLE SD, in most low-power examples...
Hi,
I am having a problem where the client is unable to receive notification from a peripheral after the softdevice in the peripheral returns 0x3002 after a disconnect....
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of openThread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure...
I am Rattana. I have some project for Bluetooth communicate with mobile phone. Then I will use BC805M(nRF52805).Nomally I connect my MCU with HC06 and I use MCU because I...
Hello I'm now trying to implement the IOS Phones (Central) - Device (Peripheral) liver UART using Multiple Connection - Nordic Uart Service. Devices tried to send a UART signal...
