I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
Hi,
I am using mechanical QDEC which doesn't have LED and simply A and B pins. After going through forum I set the QDEC confguration as follows.
Then changed function...
When I tried to compile bootloader example code of sdk bootloader_secure, I am facing some of the errors when I tried to compile using Segger Embedded Studio , which could...
I develop my own project on nrf51dk sdk12.3 on ses.
1.My app project use experimental_ble_app_buttonless_dfu project after add <ProgramSection alignment="4" keep="Yes" load...
Hello Nordic,
I have a problem regarding UARTE0 and Easy DMA with SDK 12.0. I know, this is an old SDK, but unfortunately I'm not allowed to change it.
The TX part works...
I previously tried combining USBD CDC ACM with 802.15.4 under Softdevice, and this did not work.
Now I try combining examples/peripheral/peripheral/usbd_cdc_acm with the...
Hello,
I want to put my custom board to sleep mode after writing some data through NFC and wake up from sleep through NFC. I have successfully write data through nfc. To...
Hi,
I am using NRF52832 to read the sensor data (BMI160 accelerometer sensor) by using I2C.
I try to send the sensor data to mobile by using BLE_UART. upto this i finished...
Hi, is there a way to upgrade zigbee firmware on a NRF52840, using BLE? Id like to press a button a number of times on a zigbee device and enable BLE to upgrade firmware via...
Hello,
I have bough the NRF52 dev kit, and I'm planning to use STM32 to let it enabled by bluetooth.
I'm very beginner and I don't know how to use it to connect with...
Hi, all
i have using adxl335 sensor interfacing ADC ;i have done code ,i wanted to know is it correct or the way i have developed the code can any one suggest me.
How...
Hey guys,
I have followed this tutorial that shows how to modify advertising data, and more particularly the name.
What I want to do is set a name in the beacon example...
I've added a HID service in my project.
I see a lot of messages
<00> debug> nrf_sdh_ble: BLE event: 0x57.
in the RTT Viewer.
What does the event 0x57 mean?
Hello All,
We are designing a product based on Tracking device, for this we use nRF9160 module & use controller #nRF52840 to send AT command for LTE and GPS.
We do not...
