Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I'm using the latest nRFConnect SDK w/ VSCode with a custom board connected to via a J-LINK. When I look at the call stack it only shows the current thread. I can see thread...
I would like to know when each BLE advertising event has ended for possibility stop after specific number of events and to be able to update advertising data between events...
Hi Dev Zone !
I am actually using nrf52840-dongle for wireless communication with the protocol Enhanced ShockBurst (ESB). I would like to connect an external antenna to...
I am getting ready to release a nrf52 based ble product. These products are connected to a BLE to wifi bridge. So I can talk to them at any time.
I have been using the secure...
I've been evaluating the nordic SDK. I was able to install 1.6.1, 1.7.0 numerous times. I've been working with one of the individuals there at Nordic, and I wanted to do a...
The peripheral application I'm working on implements a service which must handle multi-byte incoming messages from a central device and would welcome a pointer to any example...
Hello
I found a possible bug in NCS 1.7.0 which was introduced in PR #5353 .
1) False UNKNOWN event when disconnecting
The "invalid cell id" check leads to an false...
Hey
I'm using the softdevice s140 in my project (and the latest SDK 17.x).
I successfully enable the softdevice and am able to start an advertising (as peripheral). However...
Hi
The baseline current consumption running the azure_iot_hub is very high.
I'm using nRF Connect SDKv1.6.1. The sample connects and sends data to azure as expected. But...
Figure 4: Memory layout
Shows code RAM beginning at 0x0080 0000 but nRF52832 Engineering A Errata 33
"Code RAM is located at address 0x0800_0000".
Additionally 0x2100...
Hi,
I am developing a product based on nrf52840 soc as a central Bluetooth device. I want to connect to a Bluetooth device (as a slave) while it is advertising, but unfortunately...
Hello everyone, i'm trying to run the button sample with Pull_up on the pin P0.27 i did the wiring like below
power->VDD nrf-HV
GPIO->P0.27
i attached a resistance between...
Hi,
Does nRF5340 require any calibration in production line in terms of below items. If so could you share any documents on them
- Gain for the RF front end
- Crystal...
Hi, helpies
I am currently workibg on nrf52832 board and now there are some changes in the hardware and we are left with pin shortage,so we planned to upgrade to nrf52840...
