Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi there,
Currently, I am getting an error with a low power node when the remote cannot configure through another regular node in a mesh network. What causes me to get this...
Hello Nordic support,
I would like to use the APIs in IEEE 802.15.4, especially mlme_scan_req in nRF5 SDK for Thread & Zigbee for a ZigBee application in order to scan for...
I want to use the Nordic UART/Serial Port Emulation over BLE to communicate to a windows or linux host computer.
I see Andriod and IOS haveapps available to support Nordic...
Hello,
I have upgraded my project from nRF_Connect 1.5.1 to nRF_Connect 1.6.0.
It runs on nRF9160 and I use RTT viewer v7.50a.
The problem that I see is that the logs...
Hi everyone,
To give a first introduction, I have been working with this development kit for a while now. I'm trying to develop a Zigbee device and I'm very close to finishing...
Hi,
I want to scan for broadcast messages from a specific device that I never connect to (not bonded to for sure) and I want to filter out messages from other devices! to...
Hello,
In my project i want to interface M24C16-R external flash using i2c
I am using SDK 17.0.2 and nrf25832DK
So, the problem is first i have used "twi_scanner"...
Hi,
We are working with nRF Connect SDK v1.5.1 and an nRF5340 device. We want to use the hci_rpmsg sample from the SDK to run in the net core, but we want to move the directory...
Hi,
I saw on this answer that the pins for SPI should be chosen among non "Standard drive, low frequency I/O only". But from the default ones only SCK is not low frequency...
Hi all,
We have developed a BLE project on nrf52810 that uses S112 and we want to port this project to the nrf52811.
Which code changes should be made? Is there any SOP...
Hello i'm looking at the current consumption with the nrf PPK2 and i'm observing a strange behaviour :
the nrf advertise for a while then should stop the advertising using...
I installed Nrf Connect App for Windows. I was OK initially. Then I saw there're updates available so I let it update itself. Now it has a version conflict. When I try to...
Excuse me:
I want to implement the application allows a connected USB host to remotely tell the app to reboot into the bootloader to allow it to be updated via DFU.Can you...
Hello,
in my application I need Real Time Clock whit date and time.
How set and get the current date and time.
Where i found an example?
Thanks in avance
Best r...
Hi, faced a problem while transferring a project nrf52810 on nrf52832. I changed project settings and file paths comparing projects. The connection with the phone became very...
