I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
hi... i want to store data in flash , i will get the data periodically . Even i am writing data to flash using write command ,when i am trying to print the data which is stored...
I am using nRF52 DK.
When I do 2 analog inputs using the SAADC, I noticed that, in the SAADC callback, p_event->data.done.p_buffer[0] corresponds to the correct SAADC channel...
Hello,
I use a configuration with multiple NUS_C and NUS links. When I receive events, how to know the index ?
I have seen mutiple exemples using conn_handle but in a...
Hi teams,
I am trying to automate preferred mesh configuration for each node.
For example, if I use nRFMesh app, I should 1) bind application key to each model, 2) set...
Hi everyone,
During test with my small mesh network, I found that adding all-nodes to subscription list is prohibited by Mesh Specification.
In Mesh Profile 4.3.2.19,...
Hi:
I use the sdk https://github.com/jimmywong2003 to make a bin file and then run the command of ./UartSecureDFU ttyACM0 application.zip to updgrade in linux
It always...
Hi
if one searches the examples using the timeslot API, every application seems to do it's own timeslot cleanup. Also documentation is not very clear about this.
Best...
i am using nrf52840 dongle with uart using ble_app_interactive example,
but after commenting only uart with cli is replying with some text as shown in image .
For the...
Hi! I'm using S140 and I'm using the ble_advertising module to set up advertising.
This is my advertising_init function which is working properly until I uncomment the enabling...
This is perhaps not so much a question as a request.
The FDS event handler, type `fds_cb_t`, has only one argument, type `fds_evt_t`, unlike (say) the two wire event handler...
Hello,
I would like someone to explain to me payload for Zigbee cluster library (Zcl)
i was following this guide to control my lights:
https://infocenter.nordicsemi...
I am trying to connect to another type of board via the UART on the development kit. However, there seems to be a voltage mismatch. Are the nRF52840 development kit UART signals...
hi... i want to store data in flash , i will get the data periodically . i have merged the ble_app_uart +fstorage example . Even i am writing data to flash using write command...
Hi everyone, I have a question related to the power supply of nRF52840 DK
I want to operate the nRF52840 DK with a LiPo battery (for experimental purposes). Is it possible...
The antenna is mechanically symmetric, but as I understand not electrically symmetric.
Is this an errror ?
www.fractusantennas.com/.../UM_FR01-S4-210.pdf
Chapter 5:...
