I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I want to use the register of Nordic's P0 port directly to set 1 or clear 0. Like this,
p_reg-> OUTCLR = clr_mask;
P_reg - & gt; OUTSET = set_mask;
p_reg-> OUTCLR...
Currently we are developing against hardware sensors etc. that we have installed in our warehouse
It would be great to be able to develop remotely (ie. from home) without...
Hello Nordic Support Team,
I'm using nrf52840 DK for DFU update over ble with nrf5 sdk previously it was working fine and i was using nrfutil tool to generate settings,...
Hi,
I have downloaded the nRF5 sdk v17.1 and used the peripheral blinky example with pca10056e and S112 soft device and modified the preprocessor defines and this example...
Hello Everyone,
I am working on NRF52840 and we had enabled the APPROTECT feature in our firmware. The code for implementing this is as follows:-
void init_mem(void) ...
Hello,
I know that the bt_ctlr_set_public_addr() interface needs to be called before enabling Bluetooth, and this bt_id_create() .
But I read the description of bt_id_create...
Hi,
The nPM1100 Specification states in section 7.2 that:
An application should not be supplied directly from VBAT because it can disturb the battery charging process...
Hi everyone,
I wish know how i can set BLE_GAP_TX_POWER_ROLE_ADV at peripheral and BLE_GAP_TX_POWER_ROLE_CONN at central on UART example provided on nRF Connect SDK v1.6...
Hi All,
I am working on a nRF52832 project using SDK 17.0.2, SD 132 and a custom board. I added secured bootloader functionality according to example. At start of the main...
Hi everybody,
I am with two custom oards that include nrf52840 chip, one acting as central and one as peripheal.
This example is custom to get multilink, for that i save...
Dear team ,
i am working on ble_app_lbs_nus_c project when in this project try to add nrfx_timer.c file
we got an error like this.
Building ‘ble_app_lbs_nus_c_pca10056_s140...
I was reviewing the MNO certifications, and I see that there have been no updates since 1.5.1.
1) Is it acceptable to use 1.6.1 with AT&T?
2) Is certification planned...
Hi, I am trying to update the battery level through an example of the HID keyboard of nrf52832.I'm trying to connect 3.3V battery to SAADC AIN0, but as shown in the picture...
Hi, I have a question about nRF Connect Programmer tool.
[Description]
The device memory layout shows the address range as "0x00000000 - 0x00100000 (size 1048576 bytes...
