Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Please find attached several fixes for bugs / incomplete protocol implementation in the MQTTSN stack that we have identified for inclusion in future versions of the SDK. ...
The Thread SDK is pretty awesome! :) However, It does has a bit of a learning curve for me because it only uses UDP instead of TCP.
While searching I found an MQTT variant...
We're developing on a custom NRF53 board. With the I2C bus disconnected from all peripherals, but with external 10k pullups connected, we get the following waveform when attempring...
Hello,
We are working on a research project in Sheridan College to create an indoor positioning system using BLE 5.1’s Angle of Arrival feature. We noticed that nRF52833...
Hi,
I am using the nrf52840dk trying to connect my bike power meter over ANT+, to then forward data to cloud (will be using the nrf9160dk and then the thingy91 once I get...
Dear Support,
I'm evaluating a tiny BLE chip that we can do:
reading multiple three SPI sensors: pressure sensor, accelerometer, and FRAM.
So with your BLE chip...
Hi,
Using 52833 it seems that sometimes the radio quits responding, ie, it is in NRF_RADIO_STATE_DISABLED state and there is
no obvious way to get it out of that state...
Hello,
I'm trying to program the ble_app_uart example program from SDK 17.0.2 in Segger Embedded Studio using softdevice 132 to a custom PCB (with the nRF52832 chip) using...
Hi,
I am using nrf9160 to handle the MQTT protocol and collect the data packets from another microcontroller using the UART interface.
Sending the data to the server using...
Hello all,
since Tuesday I'm trying to get the example project ble_app_uart_c (SDK Version 12) running. Meanwhile I can compile the project without errors, but when I flash...
I am trying to set up the nRF52840DK to interrupt on the comparator input on A0 going above the threshold. I figured, I think, how to set the comparator up but I am havin...
Hello Nordic Wizards,
We are in the final throws of a project preparing to go to market. However we have identified a "strange" problem.
if the batteries driving the board...
I keep getting this warning message while I'm running the peripheral_uart sample on a nRF52820. Anybody had experience with this? I assume it has something to do with my heap...
Hello,
I would like to synchronize my mesh server's current time with my smartphone. It is possible using nRF Mesh Mobile Application ?
I saw on the mesh models list that...
Hi, I want to use TrustedFirmware-M as a secure backend for an application that uses Mbed TLS in the non-secure domain, and this seems to be artificially limited - the MBEDTLS_USE_PSA_CRYPTO...
