Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi,
I have been working with a nRF52840 DK up until now, but I need to change and move to a nRF52833 DK. I wanted to adapt my code as they can both use the softdevice I...
Hi all
I'm working on a project based on the nRF52 chip and I'm encountering
If the system runs out of battery or no buttons are pressed within a timeout the system has...
Hello
I made an application on the nRF52 sdk, which works correctly.
Now I want to add the ability to update the firmware via OTA bluetooth.
I followed the instructions...
1. Using Zephyr, trying to config SPI_3 of nrf9160 more than 1MHz for flash interface.
2. Ending up in faults.
3. We need to configure SPI_3 as master with freq > 2MHz...
hello!
im using sdk 17.0.2 with softdevice s112 in our customized board as i want to work for long range mode,so i need extended advertisement ie no available in s112 so...
Hi team.
we are developing project using nrf52 mesh sdk including 1 port nRF52840 and other nrf52 devices. we are finishing dfu mesh for devices.
The nRF52840 gateway...
Hi,
I'm developing a multi-scene application by reference to the "Light switch" example in nRF SDK for Mesh 5.0. The first screenshot show my Elements & Models structrue...
I would like to use the USB dongle with the Openthread CLI example (and eventually an open thread app) as the SDK is just too big and overpowered for my prototypes, I would...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
Hello,
I'm trying to add a rotary encoder support to the HID keyboard example on SDK17.0 with some custom hardware utilizing the NRF52840. It works well to send the requested...
Hello,
We updated NFC in our product to use SDK 17.0.2 Type 4 NFC, and we are getting customer reports that reading NFC fails on devices which used to work just fine on...
I want to create mouse&keyboard set based on nRF52810's. Keyboard that will be used is from broken laptop with 24-pin connector. Does nRF52810 have enough pins for that? ...
Hi,
I have setup a device with usbd_cdc_acm to communicate with a computer throw usb port.
First, when the device boot up and the usbd init, all works fine and the device...
Hi, I need to select a BLE+ANT SoftDevice for nRF52805. I have read link1 (All nRF52 Series Protocol Stacks) and link2 .
Questions.
1) Why I cannot find S313 from link...
